Search results

According to Messicks it does....It would have been the original, non-superseded part number.

Currently a used one for sale on ebay right now...

Give Adams small engine of Greenwich OH a call at 419-685-2264. He is currently parting a L3010 out on ebay. Also note this particular part was used on 26 Kubota models. So when calling around for salvage, you're not just limited to one off a L3010. Messicks shows the 25 other models you'll...

The driveline kubota uses for mid-mount mowers is smaller than 3-point implement drivline like your Amazon link. It's probably metric and uses an oddball spline count. Whenever buying a used Kubota mid-mount mower, always make sure it comes with the complete driveline because most of the parts...

I believe the stock size would be a group 24. I also run a Marine battery (9A34M) due to large reserve capacity and the aux screw posts. After modifying the battery tray, I was able to squeeze this group 34 battery in there. If you have a HST machine where the battery is under the operator's...

In my case, I have a 9K LB winch that draws a few hundred amps under load. I'd get three full pulls out of the stock battery/dynamo combination before it drain it to the point of not being able to start the tractor. No longer an issue with an oversized battery and 60A alternator. I've also...

There are still some leftover Kubota parts out there to convert these machines to an internally-regulated alternator. There is a huge improvement with charging over the dynamo.

I agree and fabbed up some winch hitches that bolt right to the frame. The frames are quite beefy and stable.

Just checked Kubota's website and Paul is correct with the two models he provided. You need to be on the lookout for one of them.

01123-50820 doubles as the neg cable bolt and support frame bolt.

Mine has two bolts at the top and six at the bottom. Some screw in from the bottom. I remember one or two broke off in the process due to rust. That particular area rusts quick if your battery leaks acid. I had to replace the support and battery tray because it rusted to nothing. Also, you...

That pin simply lifts out, but yours looks rusted in place. Soak it with penetrating oil then try again. You might try a large vice grip players to twist it out. Wire wheel it clean and grease it well before installing. I’ll try to get some pics of the support mounting locations tomorrow. I...

I will echo what others have said since I also run winches on my tractors. You really need to keep an eye on how the tractor is reacting when winching. Even a smaller 3K winch like yours has enough power to damage your machine. Always mount front winches to the frame, and rear ones to the...

Interesting, I wonder what was updated on them? I saw a new cylinder is about $1450 from Messicks and figured I could have it rebuilt for about half that. If it lasts another 22 years, that be great. I attempted to dissemble mine, but right of the bat the rod eye would not unscrew and fought...

It's somewhere in your steering cylinder. It must be somewhat common for them to fail after a period of time. The cylinder in my L3010 is currently out of the machine at the local hydraulic shop being rebuilt. If you chose to do it yourself, your looking at about $115-120 in parts. I chose...

The RC48-62A & RC48-62F are identical decks. The difference is the "F" deck would have included the front mount pto kit, the "A" would have not. The rebuild parts are still available, but some of the more specific parts (gearbox, bevel gears, mounting brackets) have been discontinued.

I run a 5FT woods blade and really like it. It's built well and beefy!

Been in your shoes about a dozen years ago. Ultimately I went with a 27 Ton Troy Bilt tow behind unit and still feel it was the right choice. Wood splitting is a slow process, so if you have a lot to do, you will rake up the hours on your machine. Just tow it to the pile, fill it up with...

I agree 100% Paul. Even tough the BX Ripper is nothing more than a fancy shaped piece of steel, technique makes all the difference in the world. When I first got it, I struggled with it and thought it was worthless attachment. Then I changed up my approach on how to use it and it's much...

The paint job was not altered. The morning sun was shining in a little so maybe that gave it a little more pizazz. I didn't do the repaint, but you can tell all the decals were masked over. NOS decals are super difficult to source, and repos are not as accurate as the originals, so masking is...