Search results

Hello Jim. Where exactly is your gear case leaking oil. You have three O-rings behind the gear case for the oil passages and the gasket for the cover. I would use the Kubota brand gasket sealer. You can hold the O-rings in the cover with the small amount of grease. Good Luck Lance

Hello I have a block. I can also make the hoses you need. Send me a PM with you email and I will get back to you . Thank you Lance

Hello Neighbor Have the battery checked.What do you us the tractor for. Are you using it in the vineyard ? Lance

Hello Chris As wolf man said use a pipe or 1" steel rod that goes all the way down in the housing to nock it apart. Most die grinders will be to big to get in and clean that edge up. Harbor freight sells a small dremel tool set that works great to get in small places like this. I just repaired...

Hello I have a complete front axle out of a B6100DT. It is the same as a B7100DT. If you are interested send me a PM. Thank You Lance

Hello Did you do any thing with the lines on top of the injection pump.Check the nut under the line going into the injection pump. It takes a 19MM wrench.Check and be sure it is tight. If it is lose that cylinder will not fire. Some times when bleeding the system these nuts come lose. Good...

Hello The oil slinger is just what you see. A flat washer. Good Luck Lance

Hello Your tractor does not have a filter on the left side . It should have a filter close to the hydraulic pump on the right side. It's a cleanable screen. It has a cap on it you remove and a spring and the filter should drop out. Be sure your filter has a rubber gasket on the top were it sets...

Hello I am in your back yard almost. Send me a PM and and can help you with you clutch problem. Thank You Lance

Hello If you go to the L2350DT Parts book page 100 is my book. You will see the block you need to add . Part # 32400-99810 It goes right under the seat were the pressure line comes from the hydraulic pump.You will remove the round cover and install the block. You might check with the company...

Hello Wolf Man is right. The first thing to do is be sure you have sleeves. I have never had any luck pulling sleeves in a Kubota engine. The sleeves will need to be bored after installation so I always have the machine shop remove them.They set up there boring bar offset to one side and bore...

Hello I am parting out a L2350DT. I believe it is the same motor as your L2050DT. If you would like to send me a PM and see if it will work for you that would be great. Thank You Lance

Hello Bill You will need a special aluminum block that is drilled for fitting that replaces the existing block on you tractor. The new block will have and in and out to you loader valve . You just run hydraulic hoses from the block to the loader valve.If you send me a PM I can supply you with a...

Hello Are you looking for the arm that ataches to the rock shaft (splined cross shaft). If that is what you are looking for , I have one. Thanks Lance

Hello Grant I see you are still working on your seat. Here a picture I took today of a tractor I was working on. L 235DT ,seat belts bolted the springs. Hope this helps. Good Luck Lance

Hello Bill I repaired a L225 a few year back with a taper lock agreement.I believe we used a 1" taper lock with a chain coupling . The taper lock will lock down on the splines and not spin.You can get these parts at your local bearing supply. The unit we repaired is still in service.The other...

Where's Hudson. I see all of his post have been removed. I sure enjoyed readings his post.

We are paying $2.25 at Costco and $2.45 most other places here in central California. I just paid $3.45 on the coast of California. We are paying $2.99 for propane , what are others paying ? Lance

Hello Bonner You may need to use a gear puller on the hubs.The only way to replace the rear axle bearings is to remove the rear axle housing from the unit.This is not a small job. The bearing are pressed in from the inside of the axle tube.If the outside one is bad I am sure the inside one needs...

Hello I am parting out a L 275 DT. I don't have a hood or side covers. I do have many other parts. As you get going on you project let me know what you need. Thank you Lance