Search results

Hello What type of work are you doing? Do you have a front loader that is running off the tractor hydraulics?Why did you change the pump? What do you have on the three point? The filter in the bottom of the transmission is new? After running for a hour is the transmission case to hot to...

It is very easy to remove the front end. Support the tractor under the transmission. If you have front weights , remove them. It is best to remove the hood. Remove top and bottom radiator hoses,remove head lite wires, disconnect battery cable, remove the two side supports that go from dash to...

Hello Stubbyie has it right. The bolt kits (318-586A) are about $20 each. You will need 2. It is real cheep insurance. Original equipment blades are about $50 each.They do last longer than some of the aftermarket blades.If yours can be sharpened that is the way to go. The other thing I would...

Hello The creep speed transmission was dealer installed. They are vary easy to install. Basically remove transmission cover and replace with creep transmission. 30 years ago the B 7100 with a trencher was a vary popular tractor in all the rental yards in my area. I have never seen a problem with...

Hello 24 MM or 15/16" Good Luck Lance

Hello Have you checked the compression. A vary common problem with these older tractors is sucking dirt .You may look inside the intake manifold for dirt. It dose not take much dirt to eat up the piston rings. Have you checked the valve clearance. Something else to check is the adjustment of...

Hello You have 4 drain plugs and a filter.one drain plug on the transmission , one on the drop box ere the 4X4 shaft comes out.On the rear you have 2 more , one on each finial drive housing. They take a 14MM wrench.You also have a filter that is cleanable.It is located on the side of the rear...

Your are correct. Take the cover off the side. Remove the two 1/4" bolts that hold the valve in the box. Remove the rubber boot from the Handel remove the female quick couplers and then remove the valve from the box.the best thing to do is have a shop that makes hydraulic hoses make new ones for...

# 4 is pressure in to the valve # 1 is return. Good Luck Lance

Hello I would think you have pressure hose and the return hose reversed. Good Luck Lance

Hello Lenny You may have the main bearing housings out of order. The front one is smaller then the rear one.Email me and I can help you with this. lancenewhall@gmail.com. Good Luck Lance

Hello If that is what you want to do, I would take the hydraulic pump off the tractor and put a blank plate in it place.Do the same were the large line comes off the side of rear axle housing. The smaller line coming from the pump with the block under the seat is the pressure line. you could...

Hello I am not talking about a lose line. If you go to the top of the injection pumpwere the lines attach there is a fitting the takes 19 MM wrench. Check the center one to be sure it tight. Also have you checked the valve adjustment. Good Luck Lance

Shaun If the line was lose it would leak fuel. What I am talking about is the nut that holds the delivery vavle on top of the injection pump. If the nut is lose that cilinder will not fire. Good Luck Lance

Hello A vary common problem is the delivery valve nut on top of the injection pump. If you are having problems with #2 you will need to remove the 3 lines from the top of the injection pump. Check the nuts were the lines attach to the pump. They are 19mm . Be sure they are tight. Even if it...

Hello The suction screen is just to the right of the large hydraulic hose you talked about removing. There are three bolt on the bottom of the housing you need to remove. You should find a spring and a metal screen with a removable manganite in side of it. Clean them and put back together. You...

When you have this problem what do you have on the three point. Does it change if you lower the three point. Does the loader have a front pump or run off tractor hydraulics. Lance

Hello Do not run the tractor until you fix the problem. You have lose the prim and the pump is running dry. Just remove the large pipe from the top of the pump and pour a little hydraulic oil in to the pump. Also check the filter screen and clean . How many hours do you have on this tractor...

Hello I have never seen this type filter on a L245. I am parting out many l245 tractors.if you would like to change it to a Spinon filter I can send you a filter and base for $25 plus shipping. Thanks Lance 209-711-4066

I think you will find two more bolt at the top of the transmission. Good Luck Lance