Snow blower question

[torch]

Check all bolts for tightness.
Also, my B2782B front mount blower's reduction gear bearings set screws tend to loosen. Check bearings set screws.
Grease all grease nipples and pto shaft body.
Lubricate drive chain(s) as per maintenance manual.

The PTO shaft at maximum extent should have at least 4 - 6" overlapping shafts., and should never bottom out at minimum length (max height raised) of snowblower.

What he said.

I would add: use chain-specific lubricant on any drive-chain. And after many years of use, you may need to replace the shoes or cutting edge.

Depending on how much road salt the blower has seen some scraping and painting may be warranted. And if you deal with wet snow, an occasional spray of SnoShield, cooking spray or similar inside the chute helps keep the snow from packing into a jam.

Power chute rotation and/or deflection may add a bit if they are present. The specifics depend on if they are hydraulic or electric, factory or home-made. If they are not present, you may want to add them -- especially if you have a cab.

 

[Bearcatrp]

Its practically new. Used once according to him. Will go over everything if I get it.

 

[PHPaul]

Maybe I could get taxed on "Current Use"

Do they do refunds?

 

[Bearcatrp]

Do they do refunds?

Only for the limp folks

 

[imarobot]

Only for the limp folks

I'm good then!!!

 

[Bearcatrp]

What he said.

I would add: use chain-specific lubricant on any drive-chain. And after many years of use, you may need to replace the shoes or cutting edge.

Depending on how much road salt the blower has seen some scraping and painting may be warranted. And if you deal with wet snow, an occasional spray of SnoShield, cooking spray or similar inside the chute helps keep the snow from packing into a jam.

Power chute rotation and/or deflection may add a bit if they are present. The specifics depend on if they are hydraulic or electric, factory or home-made. If they are not present, you may want to add them -- especially if you have a cab.

Silicone work? Used that stuff on my walk behind years ago.

 

[nbryan]

Silicone work? Used that stuff on my walk behind years ago.

As mentioned, per my blower manual, I use winter grade chainsaw bar oil. Spec is to apply every 4 hours operation, which I regard as a max time between applications.
I keep a squeeze bottle of chainsaw bar oil in the tractor cup holder, and whenever stopping the blower and dismounting give it a squirt or two, always quietens things down some. I use under 1 litre (US quart) of bar oil a year on average.

 

[nbryan]

Its practically new. Used once according to him. Will go over everything if I get it.

Being so new, after some solid workouts check the drive chain slack is per spec.
Get 1/2 dozen each Drive Shaft shearbolts and Driveline shearbolts. I'm confident you'll thank me.
The manual is your friend.

 

[Bearcatrp]

Brought it home this morning.

No manual so need to find one. He let it sit out back for almost 2 years. Just finished greasing it up. Use chain bar oil for now on the chain, which needed it. 2 zerks on each side of the auger popped off greasing it. Copper. Will replace them tomorrow with better ones. Here are some pictures of the shaft lowered then 2/3rds up.

will I need to cut the shaft or can I leave it and remember not to lift all the way up?

 

[imarobot]

Brought it home this morning.
View attachment 164907
No manual so need to find one. He let it sit out back for almost 2 years. Just finished greasing it up. Use chain bar oil for now on the chain, which needed it. 2 zerks on each side of the auger popped off greasing it. Copper. Will replace them tomorrow with better ones. Here are some pictures of the shaft lowered then 2/3rds up.
View attachment 164908 View attachment 164909
will I need to cut the shaft or can I leave it and remember not to lift all the way up?

If it's too long, cut it so you don't forget.

 

[Bearcatrp]

So how do you cut it? Hack saw? Do you do like 1 inch at a time until it fits when raised all the way? My 1st time dealing with this so don’t want to end up buying another shaft.

 

[imarobot]

Without you having the manual, I don't want to mislead you so I will leave that the more knowledgeable people on this site.
You should be able to find the manual somewhere; it will be valuable information overall.