Search results

I had these threads saved that relate to tire sizes and ratios,there may be something of help in there? dave http://www.orangetractortalks.com/forums/showthread.php?t=4929 http://www.orangetractortalks.com/forums/showthread.php?t=853&highlight=b6000+tire...

Any help? welcome to the forum dave http://www.tractordata.com/farm-tractors/001/8/4/1840-kubota-m105s.html

Yes thats how I read it but would you not agree that they are over kill to hang chains on? now the hooks are there,there is a danger of anyone else using the tractor using them to tug with. dave

If I appear to be a little negative here I am sorry but from what I can see the mod has gone some way to spoil the tractor. Apart from the issue of welding on to the rop,the high positon could pose a some problems if one was tempted to hook a rope/chain on them. If you look at the clamps above...

Well I guess I should title this post: what not to do on your kubota today;) I had been clearing some ground when the old girl slipped off the edge. First two pics show just how far a B7100 will go over and not tip, in the second two I had to take off the front weights and mount them on the...

Did you just buy the tractor,did it have low pressure and thats why you changed the oil.When you changed the oil did you also change the oil filter with one that has the correct relief pressure? The oil sender may also be faulty so you need to screw in a good mechanical gauge to check. dave

As soon as the glowplug light goes out don't start it, turn off the ign switch and back on again .this will give it two lots of heat ..see if its a little smoother? dave

Does the airgun have a rifled barrel,if so steel BB's will damage it. Dave

There is a link on right side of the listings,near bottom, which says report this item,I have done it several times for UK listings and they have been removed. Dave

If OP does not want the clutch and it will fit B7100 I could be interested Dave

Yeh! I thought my scanner would do it. dave http://www.hp.com/united-states/consumer/digital_photography/organize_archive_photos/tips/scanning_slides.html

What threads do you have available in your tester kit and does the clock scale go up to at least 600psi I have just done a test on my B7100 and re-nozzeled the injectors. I screwed my tester into the head after removing injectors. first test each cylinder dry then test again after squrting a...

We'll form a queue,you could be quite busy;):D:D dave

Have you checked with your revenue and customs to see how much duty/taxes you may have to pay, also the delivery Co could charge extra fees . dave

Remember to smear a drop of engine oil on the rubber gasket before tightening. dave

I suspect the tracking may be done by the network mast triangulation rather than from a gps reciever because the gps receiver can be turned off. Does the specs for you smart new piece of hardware say it has a GPS or or is GSM enabled like some ipads? Dave

Somewhere there should be some info giving the free length of the PP springs so you could compare your springs with the specs. If you can't find the specs,given that the tractor has been unused for such a long time without the clutch pedal locked in the depressed position I would take the chance...

Well if the other side of the friction disk has the same wear as the side in the photo I would consider putting it back in. Was the clutch working well before it froze? Dave

By cracking the injector nuts you have identified that not just an injector but a certain cylinder is not working correctly .I hope for your sake that the injector is at fault but it has been mentioned eariler in the thread, the fault could possibly be more serious. dave

you will need a dummy shaft with 3 different diameter steps on it, smallest to fit inside the the spigot bearing next size up for the drive plate and finally the pto plate.you should be able to rent or buy a "clutch alignment tool" or even turn one out of wood if you have the facilities. I have...