Search results

Also if you mark your spools prior to disassembly you can generally spin them 180 degrees which takes up a small amount of wear depending on the actuator lever design. Having had a quick look at the parts diagram I would have just purchased 2 x 160 seal kits, then a 150 if you intended to pull...

Tightening torques are shown in the tables in the workshop manual, page 8-G6, 364 of 391

And I should mention measuring the loader mounting points to ground, check rams and pins for wear, measure pin to pin distances on arms, some things you just do automatically, the list can go on and on.....

Absolutely correct Larry, but everyone checks the front tires because they are on the front next to the loader, and forget the rear. While the centre pivot is there on a tractor, it is not on other machines like loaders, skidsteers, forklifts, some telehandlers etc., so as a general rule, check...

As Dave says, I guess I shouldn't assume all the basics haven't been checked first!

There is a full service manual for a BX1860/BX2360/BX2660/LA203/LA243 which will be very similar and give you all you need I expect, as well as the parts manual with exploded diagrams for the LA402 here http://www.kubotabooks.com/AutoIndex/index.php?dir=Tractor%20Owners%20Manuals/...

While there may have been some movement in mounting point bolts/holes, tire pressure as noted by Ted is a common cause. Don't forget the rear tires, as they affect it as well. After all tires are set correctly, and you have it parked on a LEVEL slab of concrete, measure from front frame...

Get them replaced under warranty and tell them you want hem done every year for the life of the tractor as they are not fit for purpose. Maybe when everyone complains they may correct the issue of junk rubber.

I would guess 2000-2500 psi from the pump, (No pics or specs makes it hard) plug a gauge inline to see what the relief is set at. (It will be set to suit the mechanical limitations of the FEL) Pumps are rated in gpm, get you engine at full revs what ever that is, time how long it takes to fully...

If it doesn't have a dipstick, I'd (personally) set it half full in the housing

As per B21 per parts manual 6C060-99410 air main 32721-58242 air inner 15241-32090 oil 15231-43560 fuel 32590-38380 hydraulic return 66021-36060 HST 32721-39140 Charge pump strainer (just clean it)

IIRC wix has them on their site. Otherwise grab the parts manual form kubotabooks.com and get the filter numbers and do a cross reference. I don't think I have my info handy but will have a look.

Is there a round knob (hydraulic control valve) on this model under the front of the seat that is done up tight?

Parts manual, parts list exploded views and part numbers, Owners/Operators manual, general layout and use/control of machine, Service/Workshop/Repair manual, detailed repair of machine.

Hopefully someone with actual experience will chime in but as it's a different series engine you would have to carefully check dimensional drawings for each engine to ensure they mate successfully, and then look at flywheels/clutches etc. Some drawings are available on the web for the 70mm...

Hi, I'm chasing some pics and info on folks running 5ft approx rotary tillers/hoes on tractors up to 25hp. Reason, I have a friend with a Kubota FL850 (33") tiller who is keen to get something bigger, I told him to go 5ft, but his dealer says 4ft so he's not that keen. I want to buy his old...

But they realistically do the same job, and the physics of expanding oil and air when heated hasn't changed, perhaps a similar vented plug could be used or drill or thread a vent into the housing. The Chinese built many posthole diggers without a vent on the gearbox which spewed oil out past the...

Get it tested for the above, not it's output

This thread clearly shows a vent on the box, does yours have something similar? http://www.orangetractortalks.com/forums/showthread.php?t=25035

I don't have your wiring diagram but I'm guessing it will be like many others, I believe there is a "combination switch" (brains/relay box) under the seat somewhere, with a dozen or so wires coming from it. The starter and the shut off solenoid will be controlled from there, disconnect the...