Search results

lol..in fact..i do cover mine with grease, i have no idea why ?..other than to help wear an tear on the two matting surfaces ?..lol.

honestly ?..no...i did not..but..its all good, not mad at all, i was just trying to help. its cool :-).

ok, got it..ty 4 the words.

yeah..i only said what i said because he did say the hydro was not working at all, soo..that is why i said what i said.

i really hope your hydrostat transmission is not bad ?, if it is ?, well..its not going to be cheap to replace it !. i took a very big gamble on my b2100 a few years back, like yours, it would not move, no lift at 3pt..nothing, engine ran, but tranny was shot. after ripping it apart, 3k later...

fluid level full ?. air in system ?. worst case, hydrostat itself is bad , if this is the case ?, get ready to have a heart attack ?, parts ( or whole part ) will not be cheap from a dealer.

just inside where the pump mounts to engine, any chance the drive gear/spline sheared that drives the pump ?.

is the hydro oil full ?, did you flush the whole hydraulic oil system ?, its posb air is in the system somewhere ?. also like you said, the pump itself could be bad ?. that tube that runs from the front to back inside the frame to the back , it sucks big time !!!, i had to pull mine apart about...

yep, i purchased this b2100 for 2k seeing how it was in pretty decent shape for its age ?, thought hey..i've been restoring atv's for 30 yrs, how hard could this be ?..ha !..lol. never laid hands on a tractor, let alone a hst tractor ?!. just like you said, i had to rip it all apart just to get...

i found out the hard way, when the hst goes out in a b2100hsd ?, it gets very high dollar !. i'm sure this is with any hst tractor ?!. you better have very deep pockets if you want to either take it to a kubota dealer ?, or..buy the parts ( cheaper this way ) and do the work yourself.

not the down links...the arms that they attach too, there '' should be '' about 2-3 holes that go outwards along the lower lifting arms ?. if you have them ?, move the left side lifting link that attaches to the lower lifting arm on a further outwards hole.

you posted what i was gonna say to do, the lower arms '' should '' have a few holes made into them ?, where he can stretch the right adjustable link more i do think ?.

i'm surprised you are even able to just replace the rubber boots ?. most tie rod ends have you replace the whole tie rod end as one part, not replace just the rubber boot that is on it ?!. as for getting it off ?, as said ^^, a pickle fork ( this is what old school mechanics call them ) would be...

i run a 4 ft titan, gear driven, forward rotation tiller on my b2100, the rear pto is just a hair lower rated than what my tractor specs call for. have you considered moving your rear wheels inward ?. i can do this with my b2100.

i took the cheap way out, i made a bracket out of angle iron, drilled holes in it to bolt it to the front of my b2100, dropped an old time 12 volt lead battery in it, strapped the battery down with a ratchet strap. easy to remove and bolt back on. so far its helped out alot on the front end.

ok, after looking over a wsm ( thank's to whoever posted the link ! ), i see where this o-ring goes now !. it say's it goes UNDER the teflon seal ?, in order to get this seal off, the wsm say's to cut it ?, yeah, gonna do a hard pass on this, as i do not , or did not order i new one to replace...

Hi, can someone that has or had a b2100hst , 4wd, give me some advice on the power steering break down on how the parts go back together ?. i know where to look at messicks, i can do this, my problem i am having is one of the o-rings # 120 in this break down --> Kubota B2100HSD (Hydrostatic...

i might have been ?..this is my first tractor i've ever owned personally, so..you are prob right ?!..lol.

i have a b2100 4 wd model, and i just went through the process of switching out my turf tires to ag tires. i do not know the diffence between your model and my model ?, but it would seem to me they are about the same ?. maybe ask messicks if you can run the rims that fit on a b2100hst 4 wd model...

you will be better off just buying a 3 pt tiller. i purchased my titan for around 1500 i think it was ?, well worth the cost versus renting one.