Fixing hole in side of block

jaxs

Well-known member

Equipment
B1750HST
Jun 22, 2023
754
567
93
Texas
Joe get yourself a 110 volt wire feed flux core welder from HF, Im sure after a couple hrs of playing with it you will be able to produce a much stronger weld then the brazing your doing.
Agree with the MIG or he could get a Lincoln stick. He should also get an old sink and electric fuel pump for a parts washer.
Where have you two been during the past 1K posts? I'm sure joe would have put your advice to use.
 
  • Haha
Reactions: 2 users

Henro

Well-known member

Equipment
B2910, BX2200, KX41-2V mini Ex., Beer fridge
May 24, 2019
5,803
2,994
113
North of Pittsburgh PA
Well, at least he attracts good neighbors! Credit given where credit due...

Anyone else notice that this thread is gradually catching up with the daily chuckle thread? At least in effect.

Aside from being persistent, which is likely a common trait here, can anyone think of anything Joe has done that they would do the same way?

Have to admit that the predictions that the tractor would never run again did not hit the target...
 
  • Haha
  • Like
Reactions: 1 users

jaxs

Well-known member

Equipment
B1750HST
Jun 22, 2023
754
567
93
Texas
Who is Joe talking to?
Have you never experienced a little man 👺 sitting on your shoulder whispering in your ear? Joe has them on both shoulders and top of his head literally screaming at him. Thats why he hasn't been able to hear one word of what people have been saying here.
 
  • Haha
Reactions: 3 users

Russell King

Well-known member
Lifetime Member

Equipment
L185F, Modern Ag Competitor 4’ shredder, Rhino tiller, rear dirt scoop
Jun 17, 2012
5,409
1,441
113
Austin, Texas
Have you never experienced a little man 👺 sitting on your shoulder whispering in your ear? Joe has them on both shoulders and top of his head literally screaming at him. Thats why he hasn't been able to hear one word of what people have been saying here.
I hate that little ba$tard!
 
  • Haha
Reactions: 1 user

joesmith123

Active member

Equipment
L295DT, BX1500
Mar 18, 2023
555
151
43
earth
Last post until more funding available for next build

20241221_112716.jpg


20241221_112729.jpg


The diesel engine making so much power, it is ripping apart all the brackets that hold the loader to the tractor

20241221_112751.jpg


Can you believe this tire still holding air and working fine? You'll never believe it until you see it, and there it is

This thread represent a complete education that will allow the average joe to get the gold/cash/reward

There might be some shop building content in january, but next L295 build scheduled for February/March once funding come in

Truthful statement: this thread fixing to get printed out and put into a solid gold binder to represent the REAL EDUCATION that was stolen from "joesmith"/yourself/whoever believe

This thead will go into hibernation until the next L295 backhoe build

The L295 with the loader that was built has given back more the $2500 that was invested in the entire robot complex (loader/tractor) and is still producing cash/gold for "joesmith"




Have to admit that the predictions that the tractor would never run again did not hit the target...
You gave joesmith the knod early on to GO AHEAD, and told him that joesmith is correct

There was certainly more positive statement than negative statements in this thread

In the beginning, I remeber you saying "go joe go" even before I knew or believed in this

I dont remember any detractor saying it was not going to run/work

Maybe yall can pull statements that wer explicitly incorrect

Most statements were: "its probably not going to work"

not, "it will DEFINITELY not work"

This thread fixing to hibernate until more funding for next L295 build, or shop building content mid january

And yes, when I talk about "your" it is that voice in my head being shared with yall, talking to joesmith

In an attempt to IGNITE that voice in your head, to talk to you and get you the GOLD
 
  • Like
Reactions: 1 users

Tarmy

Well-known member
Lifetime Member

Equipment
L2800, BH76A, FEL,box scraper
Nov 17, 2009
480
406
63
Lake Almanor, Ca
Wait WHAT?

There is going to be a son of Godzilla build?

Good on you OP…you are relentless.👍
 
  • Haha
  • Like
Reactions: 2 users

Sidekick

Well-known member

Equipment
Kioti CK2620SE cab, RTV-X, BX2360, Z726XKW-3-60
Jul 29, 2023
584
563
93
N.Y,
Hey Joe. If you saved that piece of tire it may make a nice pair of sandals that could go in the fabrication thread :unsure:.
 
  • Haha
Reactions: 1 user