Search results

Greetings, Looking for some help cross referencing a cogged belt for a Kubota V2003T engine in a Toro Groundsmaster. The Kubota OEM belt is part #15469-97010. This is a smooth V-belt. This also comes from Toro as a smooth v belt. Basically, what happens in the design flaw of this machine, is...

Just throwing this out there. Depending on how much snow you need to move and where you are located, there is an option for a front mount snowblower for the B2601. We have a front mount blower on our Kubota LX2610. There is nothing like it. Put a back blade on the rear and your all set.

We have a 2601 with a belly mower at work. Nice machine. The drive over deck is nice and it's not too bad to take off. Belt changing is a pia. Keep a close eye on the gearbox mounting bolts and the fluid. Mark these bolts with a paint marker so you can see if they are loosening. Set those anti...

Welcome to the forum @rickls. I assume you first figured what tasks you were doing and sized the tractor to those tasks. We have a B2601. Purchased 3-7-22 in CT with RCK60-32 deck and three front suitcase weights with turf tires. Paid $21,638 brand new. Nice machine. Easy to maintain. Simple...

Check out this belt grinder from Trick-tools.com. An inexpensive way to get a belt grinder that is pretty versatile. The belts are super easy to change. I have used the course grit belts to sharpen rotary blades resting the blades on the top and tilting them backwards. The premium belts hold up...

Thanks for the replies. I would like to take the plug out below the thermostat housing as mentioned above. I would need the sender and gauge to match up. So far, I have found the v1505 in a B3030 Kubota tractor but the parts diagram for that model does not show a gauge or sending unit. If...

Greetings, I have a 2012 Toro MP5800D sprayer with a Kubota V1505 engine that I would like to install a temperature gauge on the dashboard. A little history with these units is its very difficult to clean the radiator. (poor design IMO). There is a dummy light and a high temp shutdown built...

Thanks for all the replies. I did not mean to open a can of worms here. I have gotten in the habit of running oil analysis on our equipment at the golf course. When this one is analyzed I will post up a new thread on it. Oil separator at 1500 hrs. We do on average 3-4 hundred hours per year on...

Thanks for the info on that. Much appreciated. I see now under service intervals #24 PCV valve then oil Seperator in parenthesis. Talks more about it on page 144. Is there a workshop manual online somewhere that is accessible for this machine? We got the open station hydro model; 3rd function...

Greetings, Just took delivery of our new MX6000 yesterday. Reading through the manual today and under maintenance there is an "Oil Seperator" that needs service every 1500 hours. Is this for engine oil or hydraulic oil? Is it DPF related? What is the purpose of this unit? I have not seen this...

Thanks for the replies. The stop run solenoid is electric powered as well as the fuel pump. I pulled the stop run solenoid at one point to use for its twin that we have here. I could swap it back on for a test. The fuel was drained and tank removed at one point to remove other parts so I need to...

Greetings, I have a V2003T engine that has been sitting in the back barn for about 5 years now. The engine is in a Toro 4700 groundsmaster. I was told that it ran when it was parked there. The problem I face is that most of the electronics from the machine have been robbed to fix other...

My father purchased an LX2610 with cab last year brand new with extended warranty. Nice tractor. While visiting him in central NY a few weeks ago I noticed that one of the hood brackets that hold the hood on back by the cab had a broken weld. The tractor has 111 hours on it. I called the dealer...

Just put the down payment down for the blower yesterday. No idea when it will be in. If anyone has install instructions of the subframe or pictures of it installed and what it takes to install it that would be great. Thanks

Yes some pictures of it mounting up would be good to know what I am getting myself into. Thanks

Yes he has some good videos. The one I watched on the snow blower on his channel he stated the subframe was installed at the dealer. Hooking the rest up from there didn't seem bad. Curious how much was prepared by the dealer prior to the video. My dealer still stated a "prep fee" even if I did...

Greetings, Setting up a purchase through my local dealer for a LX2980 snow blower for my fathers Kubota LX2610 with cab. I have watched some videos online about this blower on GP outdoors youtube channel. My dealer originally told me that the blower has to be set up on the tractor at the dealer...

More than likely a D1105-T. I have three of them here with that engine. Now you got me thinking..... I Wonder if that direct drive fan would bolt up to a V-2003-T?

Greetings, I have a Toro Groundsmaster 4500D serial # 30856-2700001xx that has a Kubota V2003-T engine. These grounds masters had a tendency to overheat if the radiators are not cleaned out every day. The next generation 4500D changed the fan setup (hydraulic). I believe part of the problem is...

I would love to have a WSM on the L305DT as well if someone has one. I do have an owners manual and an old beat up parts manual. Mine has the L1720 loader with the auxiliary hyd tank on the right side as well.