Search results

  1. K

    M5400 4WD Camber Adjustment

    This is normal. What is not normal is that your left one is not the same. I would check that the left does not have worn bearings.
  2. K

    Glow Plugs stuck on B2710

    I am sure your bypassing will work fine but I would need to know what messed up. It is not a complex system, trouble shooting should not be too difficult.
  3. K

    L245DT PTO Loses Power Under Load

    First off, my hair stands on end when I read some one grabs a spinning pto shaft. Good way to loose an arm. It is likely the pto clutch. I believe it is all accessible from the back. The pto clutch and shaft should come out the back. I am probably wrong but thats how it looks in the parts book.
  4. K

    Not sure where to put this

    Sounds more like poor setup rather than a lemon.
  5. K

    water pump seepage

    If you have the rad out you are half way to getting the pump changed. If it is weeping then it is telling you it will fail. Could be many hours or very few. If you feel any slack in the water pump bearings then I would change it for sure.
  6. K

    FEL not responding

    Turn the steering from stop to stop. That will purge the air.
  7. K

    UDT vs SAE 80

    If you have a loader I would switch the UDT otherwise it is a coin toss. Personally anything with hydraulics I prefer UDT just because it flows/pumps better at low temps.
  8. K

    Sleeve a Broken Cylinder?

    Is the block cracked behind the sleeve? If it is it think it is ruined. Can't imagine the block is not damaged and that area is critical.
  9. K

    Fuel Lubricity

    Blind faith in the manufacturer is just that, 'blind'. To assume that any manufacturer is giving the advice that will give you the most life of your machine is unwise. They are more concerned with litigation than whether you get 10000 hrs from your machine or 100. As soon as warranty is done you...
  10. K

    Fuel Lubricity

    Ya all preachin to the converted.:D
  11. K

    Lots of white smoke when starting

    How do you get to the timing marks on the flywheel?
  12. K

    Lots of white smoke when starting

    Don't forget that you can do the same damage to a diesel as a gas with the timing too far advanced. 22* seems way up there from my experience.
  13. K

    tail light bulb replacement

    I replaced mine with led for their reduced power consumption more than light output.
  14. K

    Lots of white smoke when starting

    Actually on the b3200 you can reglow after it has started. Just turn turn the key to the right one position to activate the GP's.
  15. K

    Lots of white smoke when starting

    Going by the video I would wonder if it has a glow plug that is dead or weak. Otherwise it seems mostly normal.
  16. K

    V2403 vs. v3307 Engine

    Other than the fact that the V3307 is direct injection and 900cc bigger they will both run a long long time. The V3307 is at the low end of its hp range while the V2403 is approaching the top end of its hp range. If it was mine and the extra money would not break me I would go for the 6040.
  17. K

    B1550 Runs hot / misses

    Quite possible you are getting water into the cylinder that is misfiring. It has likely been doing it a while and the cylinder is likely in poor condition. Long term antifreeze consumption will ruin a cylinder and the rest of the engine if run long enough. A tear down will be in order.
  18. K

    kubota paint fade

    Any paint with the red pigment absorbs more of the ultraviolet spectrum and fads faster. Ever noticed an old International that sat out a lot, they are more rust colored than red.
  19. K

    5740l hst

    Not that I am aware of. I believe there are several aftermarket ones but then again I might be smoking bad weed.:D By the way, good trade.
  20. K

    How heavy

    Don't think it is a posted item but a crude rule of thumb to give a ballpark lifting capacity.