Search results

Years ago right after the "SAFE ACT" was pulled over on us. I was out on my sled for a nice ride on the top of the Tug Hill. Great snow flat and fast, I roll up to an intersection an get stopped by 2 armed State Troopers with fully auto. rifles. They Informed me Dear Leader was out for a ride...

Nice pick up! Be carful if Dear Leader Andy finds out it's got concrete on it the taxes will rise.(just kidding... not really though) Have fun getting it cleaned up and working again.

Who knew that old Fluke 88 Ive been using for 20 years could do all that????

On the new Landprides you can change the blades from the top now. Im running An 1860 and works great

Now I'm in Turin next to Snowridge, That was at my old Camp in Martinsburg on the top of Mapleridge. I was way past the wind towers, about 10 years ago. I have Verizon now and on a good day maybe have three bars, if its raining two..... arrrr life in the North Country!

I had a remote Camp up this way in northern New York and had zero bars. Bought a cheap booster and still had zero bars. It was about 15 miles to the nearest cell tower. Bought a Wilson cell amp and Yaghi antenna and finally got a solid three bars in all weather. It wasn't cheap by any means, but...

Bigger than you think, my B3200 with FEL & BH just fits on my 18ft 10,000 gvw trailer. Maybe 2ft in the front and 3ft in the back, and that's to get the weight distributed over the entire trailer correctly. If I have the Wood chipper connected,it will move back to the back more.

I only have a 20Gal on my 3/4HP system and no issues. I'd go with the 50 just to be on the safe side.

Yea, already replaced the blades after hitting a guide tie for a radio antenna they had, field rocks and stumps. Of course all un-marked. Getting good at sharping the blades with a grinder and sanding disk. Do wish I still had access to my old Bridgeport Mill to do them up correctly, though.

Just started to do the same thing on my new property, 45 Acres with a road running thru the middle. Bought it last summer and have been renovating the old house and working the other 23 Acres by the house. Yesterday started to knock down the Golden Rod and other grasses that have taken over on...

A Bucket trap will get them

Very Cool Video, I love watching these little birds. I have two feeders on my deck and will sit out there and obverse them. Never have seen them taking a bath thou.

I don't know that machine, But you may have burnt out a Fuseabile link. Time to put a volt /Ohm meter to work and trace it out.

Dropped an old 28'X24' Garage and broke it apart with the BH and Thumb, Good Times for sure! I Love tearing things down. Now just waiting for the dumpsters to load up.

Find a Good Machine Shop and get two made, if one bad replace both at the same time to lessen the future failure risk. It's not a big job by any means to make those shafts.

I just picked-up an 2019 Can-am Defender HD10 XT cab, I traded in a2017 Cam-am Commander 1000 for it. I just love every thing about this machine. I did keep the track system to swap onto this one from the Commander. So far belts have never been an issue for me, even while plowing snow and...

Can't say for sure, but it's gotta be less then a new one.

Re-core the radiator and then pressure test the system and see where it go's from there. Did you fill it back up without it running? That's NO-NO always put cold fluid into a Hot motor with it running. If it was hot enough to crack the engine the cold fluid could do it, kind of like a shock.

As us Old Timers say up this way " We have two season's, Shoveling and Swatting." I'll take the winter over summer heat on any day.

With Deer and Moose burgers, it's got 'a be after 12 somewhere!