Search results

I just did a head gasket on a d722 three cylinder Ready to start, was cranking and cracked one Injector line and away it went.i knew it was about to Start, from the plume of white smoke coming out The exhaust. No fuel= no smoke. As far as starting fluid goes-get rid of it And never be tempted...

75/26 represents two batteries, 75 is a side post And 26 is a top post.very common type of battery There is a national battery group listing Do a search for BCI - battery council international Should help narrow down a battery to suit Your needs. When i need a battery, i go to my nearest Auto...

Most vehicles come from factory with some means Of tie down point. Many of them are a keyhole Slot in what is supposed to resemble a frame. Some are brackets that are removed during Pre delivery inspection. The dealer should have some sort of Reference manual for securing these machines In the...

By disconnecting fuel sender and grounding Sender wire you should be able to make guage Do a full sweep. If it does do a full sweep, i would say Sender needs to be adjusted. Will need to Come out of tank and rod adjusted. Unless Something caused the sender to hang up.

The socket head capscrews are notoriously tough Probably equivalent to an L9 grade. Drilling deeper Holes may need a pilot hole, i suggest Finding a sleeve of some kind to help center The drill. Good luck, patience will prevail.

Our hst4610 has two plates on the front with grab hooks On framerail. Rear we use 1/2" grab hooks and slip over rear Loader frame. Rear chains crossed and ratchet Type chain binders. Nothing on bucket or hoe. I would prefer implements lowered and chained Too, but supervisor will have none...

I have had good success with a rebuilder I use locally. The z750 engine is a hard engine to Find a starter for. I just did a quick search And hard to find something that would work.

First, i dont understand the reason for ballast in front tires, But to each his own. I had tubes put in the HST4610 At work. First tire shop said if tire goes low it will wreck tube. So second tire shop said no problemo.been a year and needed A little air after the harsh winter.corrosion got...

Three point isnt all the way up or down , causing Pressure problem? Or am i way off base. The 4610 loses power if 3 point is under any kind if load

I have had front wheels up, but only a couple inches Was testing my homebuilt three point forks. 700 lbs is impressive, but nerve wracking to Say the least. People end up in situations Like this every day,and it does help to know The limits of your machines,but pushing beyond That can make for a...

So, on a very soft surface it vibrates? Only thing i can imagine is a driveshaft That is out of phase.i dont think its possible With these new fangled machines. Tire pressure - lower it and see if vibration Changes.

I second the venting problem, my l1501 was leaking Out shift boot. Just this morning i found A thread about it and cleaned the vent Which was plugged solid. Worked it for an hour And not a drop. Mine was on top of housing under the seat, Threaded into casting. Some i understand are Part of the...

Thank to this thread, i repaired my only oil leak. On my L1501 the vent tube was plugged with Mud. Its threaded into the housing under the seat. Ten Minutes and it was fixed. Also got hinge welded On toolbox while it was off. Ott. Com rocks!

If all you plan on using is a hand wand, you Might consider an electric pump. I use an electric On my tow behind sprayer. I mounted my Booms on clips that pop if i contact anything, so booms Dont get destroyed. Also valves so i can Turn either boom off and use a wand. Those pumps are...

Only joined site a couple weeks ago, tempted to donate As 40 seems fair for access to a wealth of Knowledge. But, i dont do paypal. One attempted Scam is enough for me. Any other options Im game. Thanks for reading. Frank

Great idea. Looks like i need one too, use it to Carry wood to heat garage warm to keep Tractor warm. Win-win. Thanks for the photos

Im suspecting a failing bearing. Cranked over hard would Load the bearing. Dismantling the knuckle Is pretty straight-forward. A couple hours and you will know what the problem is. My local dealer is very good with providing parts breakdowns when ever i need them. That alone is what makes...

Some sort of spray lube with a cap, bungee cords One to stretch across three point arms to keep em From rubbing tires. If its wood season- an Axe. Tape and a battery cable end. I fill my box with whatever suits the tasks at hand.

I buy my wood in 8 foot lengths. Pretty easy to figure a cord from that. Plus two cords Is all my trailer is willing to carry. Made a bench to hold a chainsaw for blocking It up, now i have a sweet little tractor i pkan on building a splitter. Three point pto. Man- that l1501 is amazing on...

50, one week monday. Eyes not like they used To be.memory still good though. I know im a newbie, but not new to the forum thing Its awesome theres so many good people Sharing a common interest.