Search results

Just to be sure i am inderstanding this right the starter motor won't turn over until you move the hydrostatic pedal and it's not that the engine will not start. if its just the starter motor then the HST (hydrostatic pedal) safety switch is probally out of adjustment or it may be a bad switch...

The switch connector should be in the dash under that blank off plug to the right of your front work light switch. this is where the rear work light switch goes and if it wasn't said already you will need a switch to get the rears to work. you may need to remove the dash to get to the plug it...

The parking brake must be set and the pto lever in the rear pto only position then you can leave. edit: on page 40 of the owners manual it says to also place gear selector in the neutral position but if i remember right when i tested it gear position doesn't matter.

I am not a hydraulic guy but most cylinders are not hard to replace seals on. a pin spanner (to remove the gland end), seal pick, and some hand tools are really all you need and if you dont want to get a pin spanner you can use a pipe wrench to get the gland end off. do not use a pipe wrench on...

yeah its overkill the camera makes it look much brighter than it is but this guy has me beat post number 11 https://www.orangetractortalks.com/forums/threads/b2650-b3350-parking-brake-indicator-light.22665/ Actually my light could be brighter especially during a bright sunny day in the middle...

OK here is what I did I was having a hard time making a wiring diagram so I did not include one but its a pretty simple circuit. picture 1 is a 6 inch red led motorcycle brake light from amazon. picture 2 is the parking brake lever with the switch (sorry its a little blurry ). picture 3 is the...

yeah i added a big red led brake light to my b2650 after leaving the brake on. if the parking brake is the same on the b2301 there is a switch above the handle that keeps the brakes on. if i remember right the switch turn on the positive side when brakes are on. i used the same connectors that...

Check out messicks.com this is where i am finding this part number 31301-14230 gauge, oil sight #020 on the diagram https://messicks.com/ku/93333 Hope this helps.

Found them look in the edited post above.

well i did see it could be a shell product and somewhere i found a motomaster product on a citgo data sheet. i will see if i can find an link to both websites again. edit: here is the shell one and actually it says motomaster is not a shell product but made with shell technology...

yes the gl-4 rating should mean its be safe for yellow metals but you have to look at a product info sheet for the copper corosion test or know if the ep additive contains sulfer. I did a little research and what i could find is the motomaster gear oil is made by citgo. i looked at both citgo's...

The oil range is any where between the two holes on the dipstick as long as its above the lowest hole on the dipstick you're good. From what you describe your oil level is above the lowest hole on the dip stick so its good but if it was my tractor i would want the oil level at neer or at the...

Maybe this will help https://www.rimguardsolutions.com/beet-juice-is-better/tire-fill-chart/ enter you tire size in the interactive tire fill tool and it will give you the gallons For your tire its either 24 or 29 gallons in them multiply that by the 7.6 lbs for winshield washer fluid or 8.6...

The transmission and hydraulic system use the same resivor and use the same dipstick by the 3 point. Also don't forget to check your front axle fluid if its 4wd.

Its a radiator pressure test kit they are universal for automotive, agriculture, industrial. Or basicly anything that uses a pressurized radiator. I see your location is Canada and not the USA so Princess Auto is the Canadian equilivant to Harbor Freight here in the states. You may also be able...

Hopefully this attachment works. Here is the pdf of the B2781 and B2782B owners manual

http://kubotabooks.com/AutoIndex/index.php?dir=Excavators/ The first pdf should be the workshop manual for the kh41. I did not find anything in there about a red light though. My guess is it's one of two things alternator not charging light or oil pressure light. Looking a the electrical parts...

If you have a smartphone download the mykubota app and you can download the entire manual.

Did you check your owners manual? From looking at the owners manual there is no seperate hydraulic tank or dipstick listed. Alot of tractors use the transmission tank as both the transmission fluid and hydraulic fluid tank.

Its on page 103/ 104 of your owners manual. Its the same as the b2650 for maintaince and if you want to change fluid then go ahead its not going to hurt it. I did not change mine at 50 hrs. To put more confusion into it the service manual for my b2650 says to change the fluid and filters at 50...