Search results

Yes, this build I did probably 20 years ago and was quite involved. I was originally thinking that I could use the hydraulics that are on the tractor but soon realized that they were not going to be enough. I ended up building a power unit to go under the tractor that would replace the mower...

If a person is stupid enough to do that they should stay away from tractors.

Just for comparison I use this home built hydraulic dump trailer behind my 18 HP John Deere 345. Fully loaded with damp earth it weighs around 1500 pounds including the trailer. I have no issues going anywhere with it so would think that the op's BX could easily tow a ton considering it has...

Saw the show. Going to make a lot of folks re-think purchasing an EV.

Not sure how the pump is installed on the m9000 but often when the pump seal goes bad it dumps the oil into the crankcase. Check the engine oil level and if it is high do not run the engine until the pump is repaired or replaced and all oil levels are correct.

With the way tv cable is going up in cost you might be installing that tower to hold an antenna. My cable and internet bill are considerably higher than my power bill.

Available in 4 ltr as well as 1 ltr cans along with spray cans. I have seen it in our local store. https://www.homehardware.ca/en/37l-kubota-orange-gloss-alkyd-implement-rust-paint/p/1823941

I have not noticed any difference in the paint colors on my one year old lx2610. If trying to obtain paint you are restricted to what is available here in Canada. Other than the dealer the orange is available from Home Hardware. I also had them scan my gray hitch parts to mix up some metal...

I have to agree with the quality of YouTube videos. Sometimes you have to look at a few to get any informative information. It is just amazing that no matter what info you are looking for, there seems to be a video for it. I worked in the hvac and electrical field for many years and having...

I wonder if Kubota uses different suppliers for their blowers in the US and Canada. Both my new blower and my 30 to 40 year old blower that I had on the b7200 were almost identical in how the shear pins were designed. Both from a Canadian company. Neither has the impeller shear pin through the...

I looked at the parts dwg. Can the clip be removed and slide the impeller far enough to expose the location of the pin? If not you might be able to put something small into the hole and try to "feel" the location. When you do finally find the location, mark the shaft for next time.

What blower is this? Have only worked on front mount kubota blowers that do not have the impeller shear bolt going through the shaft.

Exactly! This is a well known issue when blowing snow. As soon as I installed the blower last winter I removed this pipe. Never had any issues. It is just part of my blower install and remove procedure.

A couple of years ago I purchased replacement Carlyle front tires for my original b7200 from a Tirecraft dealer. Around $100 each at the time.

Now that is a dealer that cares. Mine gave me a can of orange after I mentioned that there was some bare metal from the sub frame installation.

A spray can of gray paint from the dealer here in Ontario is around $60 with tax. I just took part of my 3 ph for color match to an automotive paint supplier for less than half the cost.

Certainly, you can lift them with the blower running. That is what the universals are for. I have been doing it for years without any issues. I can only imagine the wear and tear created if you had to disconnect and reconnect the drive every time you changed position. Now having said that I...

I have looked at the video and in my opinion it is operating as I would expect if not blowing dry fluffy snow. Any blower will push a bit out the side since you have a round auger in a square box. A piece of plate fastened to the bottom sides to extend it a bit more forward might reduce the side...

My manual for the LX3310 indicates that the E-21 code is caused by a lack of communication with the engine and recommends refreshing the software in the ecu.

I generally have no difficulty as mine are at either extreme ends of the shafts. Maybe write a note indicating how close to the ends of the shaft that the augers sit when the bolts are in place. Also write down the orientation that one is in relation to the other. You did not say what blower you...