Search results

Well that was an utter failure. 3 hours and two seals later, I still couldn’t get the seal to seat correctly. Both times I ended up tearing/deforming the new seal on one side. Sent the dealer a service request and unfortunately, they’ll have to come to my house since I have no way of getting...

Hi- I have a Land Pride QH05 quick hitch for sale. I bought the hitch new last year and it***8217;s in great shape and functions as it should. Asking $150 OBO. Pictures are attached. Please PM me if you have questions or are interested. Thanks!

Just ordered a pair of snap-ring pliers as it's one tool I just haven't had a need for...until now.

I'm pretty sure it's a leaky seal as I changed the axle fluid last year and put in 80W90 oil. I've gone ahead and ordered the seals (figured I mind as well do both since I'll have the tractor jacked up) and o-rings (for the final drive gear housing). Watched a bunch of YouTube vids and this...

There’s an extra lever guide slot on the right hand side where the levers mount. Thanks, overall it went really well.

Thanks! Doh! I meant hub ***128512;

Hi- I noticed yesterday there was some liquid on my garage floor, near the font of my BX1860. After a bit of investigation, I think I've determined that the right front axle is seeping near the top of assembly (see attachment, circled in red). I'm guessing there is a seal in the assembly...

Hi- I spent about 4-hours yesterday afternoon installing the Kubota rear remote kit for my BX1860. Overall the installation wasn't too bad - probably took me longer than average since I've not done this type of install before. I'd say the hardest part was making sure the pipes were in the...

Yea, those fasteners are not easy to get at. The handles can be a bear to get off - I found that between wiggling and some heat from a heat gun or blow dryer, they come right off.

Are you looking to remove the entire plastic piece? If yes, on my BX, the bolt are under the fender. It's kind of a pain with the rear tire on, but doable. If I remember correctly there are bolts that run up into the handle and then maybe one or two more.

Re: BX1860 - Looking for Instrument Panel (K2771-99000) Installation Instructions Oh, yes...look at that...slightly embarrassing as I am the original thread starter :o Thanks, I'll get back in touch with my dealer - they are pretty helpful so hoping this does the trick. Thanks!

Thanks for the offer, that's really generous! I wish I would have seen this sooner but I ended up finding a used switch that had the nut and just re-used that. Again, much appreciated!

Thanks for the suggestion!

BX1860 - Looking for Instrument Panel (K2771-99000) Installation Instructions Hi- As the subject implies, I'm looking for the install instructions for this instrument cluster (K2771-99000). I've contacted both Kubota Corporate, who told me to contact my dealer...seems corporate can't provide...

Yea, exactly, I really did a number on the plastic nut. No luck finding anything that would work locally. Damn...

Ok, thanks guys. Wish me luck!

Hi- Earlier today I removed the dash on my BX1860 to replace it with a new one. When I got to removing the ignition switch from the dash panel I destroyed the plastic nut that holds the switch to the dash (I didn***8217;t understand that this was actually a nut, thought it was part of the...

I second this recommendation - I have the 2" spacers from BroTek on my 1860. Top quality part.

Hi- I***8217;ll try to get some pictures up, but in the meantime the relay is mounted to the center pillar structure via a metal tab and the relay itself is grounded to the negative post of the battery. The fuse block is mounted to the same center pillar structure with self tapping sheet metal...

Hi- After a lot of YouTube watching and amassing the supplies, I spent part of today installing an auxiliary fuse block in my BX. I wired it to the ignition so it’s only live when the key is at the accessory position. Also, wired it thru a relay. Happy to report that it works as intended...