Search results

If you are not following these instructions from the M7040 Operators manual, try doing so before staring to get into hydraulic valves etc. My 2012 M7040 is erratic if I get impatient and try to get moving. I have a block heater which I can turn on from my home. The engine starts easily if you...

Sorry I even posted this...... most everyone is an expert and few feel they can learn. If anyone has personal questions PM me and I will do my best to assist. Dave

I agree my comparison was not the best but I was trying to respond to those who saw future problems. For those commenting on over heating the sub motor, there is this solution from Franklin Electric: Cooling sleeve for submersible motor pumps The heat loss generated by the...

The installation manual suggests using a 4 gal pressure tank pressurized at 70% of what you have the subdrive sensor to. My pump is a 3/4 hp with around 7 stages. The subdrive has settings for 1/2 hp pumps Dave

I would just make certain you are not intending to use the creeper gears for heavy work. The ones I have seem have a strong caution against it.......... loader work, pulling, plowing, pushing. Dave

I am surprised by the number of comments and differing opinions. I did not thinnk anyone much read this section of the forum. I certainly don't want to argue with anyone who thinks the system they currently have is as good as it should be but rather inform those who do not like what they...

I have live in a rural area with two brothers nearby each on their own well. One brother frequently has nieces and nephews staying over and wanting to use water at same time. Because I am an old engineer I am expected to solve all family technical issues. Franklin Electrics new Sub drive...

Could it also be a BX2380? Dave

Typically called a Rubber Nut or WELL NUT assuming part of the fitting is not metal but rubber. As the fastener is tightened down it expand the rubber part securing it to whatever hole it is inserted into. I have seen used on Vetter motorcycle fairings, fastening glass shower door hinges to...

I have a 2012 same model. Later models have better brakes but likely get emissions you don't want. I note two matters to bring to your attention. Additional rear remote would have cost more than $1,000 3 pt lift cylinder has damaged cover. I had to replace one of mine. Part number T106034812...

Denso has publishes a series of Starter Testing steps which I will attach. If you can use a multimeter these steps will help you zero in on the bad joint(s) and cables. I will also provide the charging system tests. Dave

Here are photos from owner In addition to the ground cable bolt to frame, the positive battery connection looks very messed with and may also be part of the problem. Dave

I have rec'd the battery cable photos I asked you for. Do the fix I suggested to this one connection and then try. Post if it made a big difference I will post the other photos so other forum members can review Dave

I have sent you a private message. Look for the envelope symbol in the top right corner of most forum pages. Dave

Kubota systems typically power the glow plugs when in the key switch start position. On older systems with a Glow Indicator, the glow indicator is bypassed when key is in start position to ensure GP's get max voltage. Your L2501 key switch does the same. GP's powered in preheat and start Dave

I do not think his glow plugs would work if a fuse of any type in the location was blown. In my earlier post this is the wiring diagram with no main fuse I was referring to. Dave

Are you certain your model has a fusible link? Some wiring diagrams for B6200 dont show one others do. The fusible link will have a white plastic connector and a small loop of green wire. If you don't have or know how to use a multimeter, get a 12 volt test light. It is a great tool for...

Often this is what the frame end of the ground cable looks like when someone is having starter issues. The connection is tight by useless! If your cables have these repair ends time to bye new cables. Dave

Please advise the model number of your blower. I would like to look at parts illustrations. Is the pin now the length of the round shaft..... I am guessing the ends of the pin were sheared off. I would suspect something was jamming the blower fan and this pin acted like a shear pin. I often...

Another consideration after you have modified a machine is in the future should you want to trade or sell it, prospective buyers will be wary and dealers will not want it. Dave