Search results

They didn't,..... at least on the b tractors.............BX engines are in "backwards" Ed

No, there isn't any easy way to change pto direction. (if there was we would all be doing it!) when kubota built the b6100 they put the pto higher on the back with a bevel gear shaft which changed the direction of rotation. could the parts be put into a b6000?..... I guess anything is possible...

Sounds like the "rate of drop" valve for the 3ph. Ed

I guess the hydraulics arent ant different between the 2360 and the 2660, I was thinking of the 23501 Ed Service <

Which tractor did you end up with........i like the 2660 better not only for the increased power but it sounds better AND has metal fenders! (hydraulics are slightly better too) considerally more money though!! Ed Service

Are you putting it on your L1802dt...... if so Id suggest no wider than 50 inches. Not much fun if its not at least as wide as your tires though!! Ed Service

The liners are fairly easy to remove on a kubota engine any machine shop would be able to make you a plate. Have you installed the new ones yet........ If kubota sleeves they will need to be bored to size.......guess you could do it with a ridged hone but I think you better go to that machine...

I think your tractor is pretty normal. They are unsyncronized and dont have a transmission brake so the clutch disk and input shaft will continue spinning for a few seconds with the clutch disengaged. Where you near the tornado...... I used to live in Durham and worked for Moores Garage many...

Hi On the f series tractors you can direct the return oil from the hydraulic lift into the charge curcuit to get a machine running with a failed charge pump ( not all that uncommon a failure either! I think it might be moisture in the oil freezing and locking the pump which breaks when you...

I didn't say it was easy! Kubota have tucked a lot of components in there! The bracket (150) is held on with two bolts. They come out and the bracket, pushrod and safety switch can be wiggled out. Then with patience, good luck and dexterity the rest of the parts can be worked on! Gives you a...

It is totally accessable fron underneath.sounds like the spring has came of/ broken. Incidentally, I have has some problems with 140 coming disengaged from part 010 or rattling.to fix it I slip a piece of 3/8 fuel hose over 140 just below the 90 degree bend to hold it more firmly in place. Ed

That is why the oil is so clean! The filters are doimg there job. The suction screen will cause more problems than the filter will but most owners don't even know it is there! The knob under your seat is probably the "rate of drop" control. with it you can adjust the speed at which an impliment...

Sounds like someone put a snowmobile type regulator on there. They work fine, and are a lot cheaper than the Kubota oem. Ed

That fitting is your coolant drain. In our country we have antifreeze there. Ed

Vic is right, Red-Tek or dura-cool will smarten it right up! You will need to completely replace the r134a that is in there now. Good luck buying it in the US though! Dupont has the refrigerant market completely sewed up down there. Ed

M5700 ac is marginal in hot humid climates like Florida. (they are barely good enough here in Alberta!) Make sure you are in recirc position for best performance.

We have a customer who has a L2002. Looks like a pretty nice rig and he's happy with it. You won't get much help from Kubota for it though! Ed

You can never go wrong by changing the Trans. oil and filter. The valving in the hyd. shuttles are quite sensitive to oil viscosity, I recommend Kubota UDT in any kubota with Hyd. shuttle or power shift. Ed

Does it work ok in reverse? If so it might be the High pressure relief valve. What oil are you running in it? there is a suction screen on the charge circuit on those tractors. look for a larger line going from up under the front of the hydro back to the right side of the transmission. The big...

Go for it! We have had zero problems with the units we have sold so far. There is a carb upgrade on last years models, make sure it has been done if you buy one from last year. Ed