Search results

The two rods that I mentioned are attached to the rod that the lower links are mounted on. The brackets that the rods are attached to are on the inside of the lower links on that rod. Even though the mmm uses the 3ph, you can still have an attachment on the rear and attached to the 3ph. You...

The B3200 uses the 3 point hitch to raise and loser the mmm. There are 2 rods that are connected to the 3ph when the mmm system is installed on the this B. You set the mowing height by adjusting the roller and casters on the mmm deck. The mmm is a ground engaging type mower deck. It is not...

I felt that the BX cut better than the b2620. The b2620 had a problem with the deck staying in position, cutting height wise. One day the deck dropped to the ground, and would not stay at the set height until the dealer repaired it. There have been several instances where this has happened to...

https://www.kubota.com/configurator/productselector.aspx?pgId=1 If you have looked at the above link to Kubota, then disregard it. The BX25 is more maneuverable in small areas. I started with a BX25. Then moved up, so to speak, to a b2620tlb, and now have a B3200 tlb. The BX will do just as...

:D Well, it will turn. Unless you put the rear pto in gear, it will turn. :D If the pto is engaged it will not/should not turn.

I am probably in over my head here, but: Could you put a slip clutch on the pto shaft at the gear box on cutter. If you don't have some sort of protection for your pto, a rock, stump or other obstruction will break something expensive internal.:eek:

Your brush cutter should have either a shear bolt or slip clutch. Maybe both. My LandPride brush cutter had a shear pin/bolt. My Woods has both a shear bolt and slip clutch. I believe that an overrun clutch is for older tractors.:)

IF you purchased your RB 84 new, then it is still covered by Woods warranty. Why spend your money. Let Woods fix it for you.:)

:)Just a quick search, and I found this: https://www.loaddata.com/members/search_detail.cfm?shotgunid=431&gaugeid=52&type=1&header=20%20Gauge%20(Lyman%20Slug%20Data)%20Reloading%20Data I looked at a Speer manual from 1962 that belonged to my uncle. I found shot shell loads, but no slug loads...

If you use a rear finish mower with rear discharge, and no chain guard on the discharge chute, you won't have to rake your lawn.:p The rear discharge rfm will spread the clippings around with no windrows. I put a chain guard on my rfm, because I cut in an area next to a road. With out the...

Speaking of sheared mmm bolts: :eek: http://www.tractorbynet.com/forums/kubota-owning-operating/287981-breaking-bx-blade-bolts.html

Have you checked the tire pressure on your B3030? :)

Well, for one thing: There were lots of complaints about the brake pedal being on the right. Now Kubota has moved it to the left side on the on the BX 70 series. The abrupt stopping in the the BX 50 series. It was fixed. Yes, I tkink Kubota does watch these forums.

The actual weight of the B3200tlb is right at 4000lbs. The 18' trailer is 1400-1600lbs. As you can see from the scale ticket I am under the 9500 GVCW rating on the Ranger. Not by much. When I traded my '08 Ranger for the '11, I was surprised at the amount I would be able to tow. :cool: This is...

Eric look at the last picture. The top of the page list the total weight of the trailer. Look down the column, and you will see a weight of 5490. The trailer with the 3200 weighs close to that amountt.

Alright, here is the evidence. As you can see, I am with in the guide lines of the Ranger owners manual. I have a 4.0, 4 door, 4x4, with the jump seats. I have no problem with towing my B3200tlb with the Ranger. I don't get in a rush on take off. I average about 14mpg and travel at about 60mph...

Actually the GVCW is 9500lbs on this Ranger. With the B3200TLB and 18' trailer, it ways 9250lbs per Cat scales. The little Ranger handles this combination very well.:)

dtherrien The B3300 is basically the same as my B3200 tlb. First off, I would raise the operating rpm's to 2100-2200 for more operating speed on the backhoe. I think it is normal on the boom and dipper stick overriding each other. You just have to work the controls together to get the boom and...

I think your fuel filter is similar to the one on my x-b2620 and current B3200. It is a glass bowl with a paper cartridge inside. If so, I broke the filter off of the b2620 while bushhogging. I was able to get it back on the trailer and get it home to be repaired. As I remember the entire...