Search results

:eek: There are several things on Kubota's, on your side of the pond , that are not available in the US. One of them is a mulching kit for B series tractors.

High gear is for transport, or cutting grass on fairly flat ground. You need to be in low range to climb just a moderate hill. The HST peddle is not an accelerator like in your auto. It is your gear shift. The less peddle applied, the more power/torque to move things. (LOW GEAR) The more...

You can offset the RFM to one side and get Fairly close. I use a push mower to Trim around house and trees. The MMM is better for close trimming

The mowers on the B series cut well. But there are no mulching blades available from Kubota for these decks. And you will get a lot of clippings from the mower. I have owned both a b2620 and B3200 with mmm's. They cut well, and my "yard" looks good after mowing with these mowers. But if you let...

According to Kubota's web site, overall height is 84.6". :eek:

It is specific to the BH77. I guessed that since he had a B3200, that it was a BH77 on his tractor. :D

Check your 3ph lift control on the right side. Make sure it is in the full open position. All the way forward. With your backhoe installed, that affects the way your hydraulics operate if the lift control is not all the way open.:)

:mad: Well, that link didn't work. It looks like that spring should be, about, under your right foot.:)

http://kpadweb.kubota.co.jp/kpad2/PartsInfo.do?bookCd=100K5120&funcCd=&figNo=D00100&dispType=2 If this works: It is a return spring on your HST. It is the 110 part in this link. If this link does not work, go to Kubota.com. Go to the parts section. look your B3300 and look under the Hst section...

ORANGEMADMAX If you go to Kubota.com and build your B2650, there are 2 blowers listed. There are 51" and 63" front mounted snow blowers . On Kubota.ca (Canada), there are also 2 rear mounted snow blowers. :cool:

There is pressure in the system. Either the hydraulic oil has warmed up or you didn't relieve all the pressure when you disconnected the hoses. Take the female end of the QC. Using a wood dowel or small drill bit. Put the dowel/drill bit on the dimple in the female QC. Place a rag around the...

Could your problem be an out of round tire?

You mentioned moving the plate by loosing the bolt down under the pto lever. I never moved that plate. It was set for 540 rear and 2500 mid, and moving that plate to another position would give you a third speed for the rear pto. Are we talking about the same think?:D

Are you talking about the bolt that changes pto speed to 1000rpm? If so then you don't need to make that change. Your mid-mount pto is set for the proper rpm. That 1000rpm setting is for the rear pto.

Your mmm is a drive over deck. Once you get used to removing and mounting your deck, it will be a lot easier. It is a lot easier if you do this on a concrete surface. Then again if your mounting the deck while on a rough surface the deck wont slide around when driving over it. This is what...

I think mine was $2600 in 2012. That $4000 is way off base.:eek: On build my Kubota: the 60" mmm is $2800 and the 72" is $3500, when included with the B3200.

There are several B7100's on TractorHouse. It looks like the common FEL is a 1630. If your fel is a Kubota.;) There is also an LA300 on one listed.

The fel is on and off in less than five minutes. Just unhook it on a flat level surface and release the pressure on the controls. Unhook your hoses and back away. You can take the locking pins out while sitting in the seat. Very easy to do. If you are mowing around objects that you value, then...

When the 3ph is lifted the orange arm is raised by the lower link, and the small rod on the bottom of the orange arm rotates a link on the mower that lifts the mmm up. Hope this helps you.

I have both a mmm and a rear finish mower. mmm is good if you are cutting along a fence or obstacles in your yard. You can look down at the edge of the mower and not have to look over your shoulder to see where the mower is. You will have to get down on the ground to hook up mmm. And reach under...