Search results

I believe so. The salesman told me they had "just" sold one equipped the same as what I posted. And salesmen never BS, right?

Yeah I seen that. Someone must have had a buddy that worked at a hydraulics shop lol. I really liked those Faster manifold type connectors, those are slick.

If there is no visible short on the wiring then it sounds like an internal short in the switch. Try removing the switch, remove all wires except for your power in to it and the wire going to the relay, then try the switch and see if it still blows the fuse. If not, then ground the switch and try...

As the title says, I'm thinking of buying a new cabbed MX6000, LA1065 SSQA, dual rear remotes, 4 or 6 rear wheel weights, 3rd function and probably R14s. For any of you guys that have this unit or something really close, how much should I expect to pay for it? I'm in Canada, but I'm also...

Hi Scott, welcome to OTT. If your driveway is quite steep, you might want to look at something that has actual 4WD. The GR is only AWD when the wheels are straight, as soon as you turn the front wheels a bit, the AWD kicks out to allow for sharper turns. Just my .02.

I have the 4 light setup on my MX. 2 front and 2 rear, each set on their own switch. They are plenty bright, and were complete plug and play. (My MX has a set of factory extra connectors under each fender). They came with plenty of extra harness that I rolled up and zip tied. My only complaints...

Jack the front end up and give the wheels a spin, see if you can see/hear/feel anything. A repetitive squeak has got to be coming from ether your wheels or your front prop shaft somewhere. Check for cracks on your rims or loose lugnuts, because either can cause a squeak. Look for marks on the...

He replaced it.

After looking at the manual pic again, with R4s you only have 4 different width settings, not 5 as I mentioned.

Depending on how your rim / center disc is set up now, and depending on what width you want to achieve, you might have to pull both wheels off at the same time to keep your tire orientation correct. There are no clamps. The center disc is dished and is reversible. The outer rim has the disc...

On my MX5000, I simply use a 10'x12' tarp. I enclose the whole front end, including under the belly and use a few bungie cords to hold it in place. I have it so the steering wheel and joystick can be either under it or exposed. Then I use two bungie cords to the Rops to enclose the operator...

I had a sort of related experience. I was pushing snow with the bucket over a slight slope at a bit of an angle. I pushed the fresh snow into a previous snowpile that was frozen, and the left corner of the bucket was under the frozen pile when I went to raise the bucket. Before I knew it, the...

Try lowering your 3 pt. lever a little bit. I know on my MX5000 I can hear the pump bypassing if I pull the lever all the way back to the uppermost position. I just move it ahead an 1/8th of an inch and it's good.

Same here, a lot harder, and seems like I get there a lot quicker. Maybe gravity has increased over the years?

Did you also order a new set of front rims? Or are you going to get the dealer to provide them?

I'll bet that's what happened too. But, if you notice, he also has the rear tires off of a BX1880 on it, so maybe the RC math is still within the appropriate limits. Either way, I'd still demand the dealer replace all 4 with the correct ones.

You are going to love that MX. I have an MX5000 and have been very impressed with it. Very nimble in tight spaces but has the size and power needed for heavier duties. But as several people have already mentioned they are light in the back end compared to what they'll lift with a loader, so get...

Could be just water in your fuel. Drain some fuel into a glass jar and let it sit for awhile. Drain the tank if you see any. Change your fuel filter as well.

Nah, I have the rain caps on my other tractors that sit outside occasionally, but they wear out over time and start jingling and rattling. This one is stored inside and I only use it to rake hay or plow snow, neither of which is done in the rain lol. The tractor is actually quieter now with the...

I was tired of smelling exhaust and cleaning black soot off of my loader arm due to the factory muffler outlet. So, I had a stack made at the local muffler shop and then I made up a couple support brackets to brace it to the grill guard.