Search results

bleed down overnight isn't unusual. The cylinder has a piston inside of it. The piston is not a perfect seal and fluid will leak past the seals even while not using. The amount of leakage is usually minimal-but those cylinders are small and don't have much volume, so a little leakage results...

one of the attacked was my brother, outside the fairgrounds. Pitty got loose and for whatever reason decided to chew part of his scalp off.

I may be wrong, going off of memory but I "think" flat rate for engine was 33 hours.

not I. Although I had to play with a bunch of the antiques while working for the dealer. Never fun either, trying to locate obsolete parts and such, and then having to explain to Mr. Customer that his equipment was too old for us to efficiently repair.

that's kind of like kubota service manuals. Translated from japanese to english (Jinglish) and during the translation, sometimes info it lost.

fuel level sensors were a sore subject with me when I was working at the dealer. They'd ship the tractors on a boat, around saltwater (obviously), then they'd sit at port for a while, then on a truck to a distribution hub, then from the hub to a dealer. Then sit in a crate, outside, at the...

it's got an electric lift pump which I find to be easier to just turn the key on, than to fiddle with a hand pump. But that's just me. What if the battery goes dead? It won't start anyway. What if the pump quits? It won't start anyway.

Pretty sure we couldn't get them out at the shop without removing the engine, which is a 30 minute job. Crossmember in the way as I remember. I've had about a dozen of them over the years. I just pull the motor out, gives me a good reason to give the mower a good cleaning in the area as well...

Right about that, same in this county. The social scum comes from the Little Rock area, I guess too dangerous for them there or maybe they're bored with that area, so they bring it here.

there's a coupling on the engine pulley, 3 bolts hold it on. 12mm as I remember. Remove the 3 bolts, slide the triangle shaped coupling back, then proceed to replace fan belt. Check the u-joints on the drive shaft and check the coupling for excessive "slop"-as both will cause vibration. If...

I have heard from quite a number of Texans that Houston and Dallas-and now Austin, are often not considered "texas" by traditional Texans...

18 to 20 foot you keep going longer, it gets harder to maneuver around in tighter areas, IMO also have to look at the vehicle pulling it. Once you start getting to 22-24-26 foot, the trailer gets bigger and heavier, and with a load on it you WILL want a 3/4 ton. Minimum. Can your toyota...

I have nothing to add, but I sure am glad I don't have to deal with those anymore....

many folks can't "hear" a dead miss....a trained ear can hear it just fine, but many who aren't, can't. Runs on one cylinder, sounds perfectly fine to a lot of folks. governors and linkages on the kohlers have never been problematic. to my knowledge or in my experience-unless someone has...

take the engine off so it can be done properly. A LOT easier!! address the drive shaft coupling/yoke and u-joints if needed while the engine is off too; also a lot easier with it off than trying to do it otherwise.

sure hope so. I moved here in 1989 and dad and I used to fish Lake Stumpy pretty often, and we always did well-once we found the fish. As time went on, it was getting MUCH harder to find the fish, for one reason lillies, and second the lake is/was silting in and the once deeper (6 foot+) water...

you can polish mild steel and it looks just like that. But it still rusts, just like that one did.

fairs are a gathering of, criminals in this area they are the only folks who go We (wife and I, brother, mom) do not attend, and Mom is head of the dav auxiliary, and should go. But she doesn't. Too much 'activity'. but if you want weed or coke or crank, or you want to be beaten or killed...

Don't know where youre at but here, we can call the game and fish people and they'll send someone out to do a pond study. From there they can give you ideas that will work alongside the the goal of the pond, be it a livestock water source or fishing pond or whatever. And it's free here too, no...

ain't too much out there in the aftermarket for kubota stuff in general. Pretty much nothing to my knowledge for cab glass. OEM or used is your only option, that or maybe you can get someone to cu$tom make you one used market? Glass is one of the most commonly damaged tractor parts which...