Search results

I made my own dolly however, for me it makes it easier to line everything up before reinstalling. Otherwise, you need to move the tractor. With a dolly, you just move it. Great for storage in the garage.

imnukensc is correct, poor design. I had mine replaced with the “new” coupler and it still leaked. Found that if I rocked the coupler front to back when engaging the lever, the coupler would seat better and would not leak. Issue was that the lever does not allow for the two coupler pieces to be...

Get news that all is well with your new ride. Yes, the Dealership does cost $$$. That is why most do their own maintenance. And, if there are any questions, this site is a great resource, as you can see.

That would be good. This connector, it helps to rock it back and forth to seat it well. Make sure everything is clean. Slowly engage the connector lever. It is easy to get it not seated flush.

One other issue that you might have the Dealership look at is a leaking Quick Release fitting for the FEL. Many have had leaking issues and have had the Dealership update the fitting.

I did not change the UDT fluid at 50 hours, per the manual, but did change the UDT filter and checked the hydraulic fluid suction strainer. The manual does not say to do the strainer, but since some others indicated they had debris on it, made sense to me to check it. It was fine. Just tilted...

I opted for the 60” MMM on a BX 2680 with the “drive-over option” based on what I saw on videos. What they don’t tell you is that the scalp wheels need to be adjusted so the deck will sit on the ground. Taking it off is not that bad but putting it back on ; alignment to engage the lift linkage...

I use a Swisher 60” FCM with my Bx and it works great. Off-set works for under the trees and gets into the slopping ditches, where the Bx can’t. Finish cut is the same as the Bx MMM. Use it to help cut 2 acres around the house and 4 acres of field.

Channel-lock pliers work fine for me. Just go over the top of the filter. You will slightly crush the top of the filter to get a good grip and then turn. For the trans filter, I have to put some duck tape on the inside of my strap-wrench to get a good tight fit.

I mow 6 acres, 2.5 around the house and the rest is field with trees and other stationary obstacles with a by BX 2380 and 60" MMM. The BX does great. I have a ditch to mow that is a 45deg slope that the BX can not do. Added a pull behind 60" finishing mower that I can offset that works on the...

My filter has been in for 9 months and there are no issues. Check it every couple of weeks just to make sure. No flaking or pitting of the SS.

Had both front tires leak on my new BX. Put Slime in and it didn't work. Used the Kubota branded sealer two years ago and have not had an issue since.

For the height adjustment knob, for me, I have to wiggle it back and forth to get it to turn.

Might look at Amazon. I got wheels rated at 1200 lbs for $24.00. Work well for my BX FEL.

Same leaking issue with my 2380. Coupler assy (top and bottom) was replaced under warranty. The issue was initially resolved. No leaking. RnR the loader a few times and slight leaking came back. Found that by rocking the FEL corrector back and forth a bit before engaging the locking lever...

They are doing fine. A little paint removed, but that is expected. I do remove the tightening lever when they are being used. Debris used to catch on them. Lesson learned. :)

My BX (2380) has the same forks. I have a factory edge guard installed on the bucket. Lifting logs, boulders, and yard debris with no issues with the bucket. The only problem is that they are a bit short and I can not see the end of them from the driver's seat.

Might also look at clamp-on debris forks. They pick-up pallets and more small debris than just pallet forks. Work great on my BX.

^^^^^ Would contact the previous owner and see if they have had issues and what they did to fix it. I had the same issue (leak) and the parts were changed/upgraded under warranty. Even after the "fix", there were leaks unless the connection was done correctly. I now rock the connector back and...