Search results

Yes, this is your tach drive, and also hour meter IF you yanked on it inadvertently, you may have pulled the rope cable out of the socket of ether end, or, just because it's old and grumpy and you moved it out of position that it had been in for 25 years, the cable broke. the cable is just...

I'm sure glad you asked this question, I was wondering if it ( throwout bearing ) was grease able, and had not found any info in my FSM ( I didn't look REAL hard, but I did look at the pretty pictures ) I'll go out and check mine out today and see what I come up with, as I am getting a squeal...

When selling, you can always lower the price or accept a lower offer, nothing wrong with starting high. Starting low doesn't usually work out well, kinda tough to get what you want or need that way. The art of negotiation is dying

1997 B2400HSD, 4wd, LA352 loader, RC60-24B MMM, Cammond 60" box blade 1301hrs currently ( will continue to use until sold ) FSM in print, parts manuals in PDF on thumb drive or SD card runs well, operates well, just don't use the loader or blade anywhere near as much as I thought I would...

if this machine is commercially used I HIGHLY recommend against this unless you have a really great liability insurance carrier, it is an OSHA violation and a sure way to be sued.

Ha, I forgot about this thread, 2 weeks ago clearing snow from the road and a few drives on my street, I blew 2 hoses on the loader, both for lift and lower on the loader ( yellow snow anyone ? ) Go figure, 17yrs old, it was time. $50 in parts and 2hrs last weekend I cut and made 4 new...

I converted my B2400 a few years ago, used a 40amp alternator from a Toyota forklift ( I'm a Toyota Lift tech, it was there and it fit ) My dynamo had seized and in the attempt to tear down and replace the bearings I managed to fubar the shaft. I fanagled the Toyota 'Denso alternator into...

keeping the containers as air tight as possible and in a temperature stable environment will go a long way in keeping it fresh. temp swings and air circulation will invite moisture, which will condense and sweat and then pool. this is a big killer in storage tanks that aren't used regularly...

truck has 180k on it, original driveshaft worn out due to joint caps spinning in yokes. the shaft has a double cardan CV joint on one end and a slip yoke on the other, bought a shaft from salvage yard, took to driveshaft shop to have rebuilt and balanced. first shop ( 130 miles away ) said...

replaced the caster wheel stays, new wheels, new bushings, sharpened the blades then commenced mowing the onions. this was after replacing the rear driveshaft in my 4Runner AGAIN, one day I'll find some place that actually cares and does a decent job on rebuild....... ( sorry, had to vent )

check your fuel filter(s) they may be clogged with debris ( not unheard of on a sweeper ) If this machine sits somewhere unattended where devious hands can get to it I'd also suspect the fuel tank may have an obstruction ( sand dirt, crud ) at the fuel pickup IN the fuel tank. ( I see this...

I took the other cup apart to inspect, as I did get a build kit for it as well, the detent for "float" position is in the end of the cup, the spring is in the extension housing. spring and cups looked good, detent cup and balls were a bit crudded up, so I pulled that apart and cleaned all. I...

You'll notice the hex is rounded out a bit, seems the screw is a bit soft, the thread lock compound made it a little difficult to seat the screw fully, 3/16" hex and then a 5mm hex. I stopped before it got ugly springs installed and assembled and the cup installed and my lovely assistant

Got the kits for the control valves, NOT CHEAP ! if I had seen the control valve on Fleabay before I had ordered these, I would have gone that way, these were special order, non-returnable. Oh well. new kits have EVERYTHING including the cup and bolts for the lower end of the spool ( o-ring...

LOL, if I didn't already have the parts to repair my current valve, I'd bid on that betting the reserve is $400 or better. Kubota list was $980 will keep an eye on it, see what it sells for. Thanks and as to your previous post, Husco will not sell Kubota parts direct per contractual agreement

Whew, Went to Kubota store today, parts guy was pretty helpful. told him what I had and needed and he just kinda looked at me, then says, " Ya know, I don't think I've ever sold any control valve parts " ....... :confused: UM, well there's a first time for most everything, right ? :D He...

:p last fall the last time I mounted the MMM I noticed the loader joystick wouldn't return to center. as such, it also robbed hydraulic power for the 3pt. Fast forward to today I finally decided to dig into it ( no snow this year as yet, so no need to be in a hurry ) also put a new seat on as...

Mine "weeps" a bit, age and seals don't go together. The only way to repair is to split the tractor and pull the shaft, replace the seals. Big job that I am not ready to do yet. the leak isn't bad enough for me to want to do that repair. Mine also leaks at the front axle pivot seal, I keep it...

Eric, I'm guessing this is 2WD correct aka a C3500 is this a dually or singe rear wheel ? shouldn't make a difference, but the parts geeks get pretty specific sometimes. ( dually spindle/hub assy will have a wheel adapter for the offset of the wheel, usually just bolts onto the regular...

http://www.orangetractortalks.com/forums/showthread.php?t=1530 read the above link,homework has been done, I haven't had time to actually finish the swap, I just mounted it so I had a fan and water pump. that thread was last summer, I've been waiting for the opportunity to actually do the...