Search results

Or any new Kubota under 26Hp if avoiding DPF is a priority...

I got my flat face connectors from Summit Hydraulics. They also sell the rubber covers for them. You can see what they look like on this page... https://summit-hydraulics.com/product-category/quick-disconnect-couplers/hydraulic-flat-face-iso-16028-quick-couplers/

Also is the leak the connection that slides on the connector or is it the o ring for the connection to the manifold? Last thought is the internal of the female coupler would be an o ring for sealing to the male side connector. Is there a burr or something sharp that is damaging the o ring when...

I use this for the blades on my zero turn. I found it used for about 50% of the new cost and it works really well. It makes sharpening them better than I could do by hand. I have 5 sets of blades I rotate from being on the mower to getting sharpened. I only get 10-15 hours out of them before the...

On my LX610 the back light harness can handle 10 amps and is only "HOT" when the key is in the run position.

I would just grind a box end wrench to fit... Also I have not tried this place but it's not far from me and seems to have really good prices on teeth new or to get your re-sharpened... https://www.jeffssharpening.com/

I don't see why it would not work... I would think that a series of tack welds would hold it fine. Also it's unlikely anything thicker than 16 or 14 gauge steel would be needed. If it's like my EA grapple it's only about 8-9" between the tines.

Just my $.02.... I am in Mid-Michigan I also have 10 acres but 5 of it is heavily wooded. about 2 is mowed grass. the remaining is open field that I let the dairy farmer down the road bale so I don't have to cut it. That said my usage is different for example my drive is blacktop and only 300'...

The LA535 from an LX 2610/3310 are bolt on and available new thru the sales not parts department for probably the same price you will pay for used

the LX2610 is pretty much the same tractor so you might get more success broadening the search to include that. If it's engine related parts from any D1305 MIGHT also be a help. The differences in the different D1305's would be mostly with fuel settings of the pump along with the accessories /...

Find an agent that specializes in Commercial insurance. You should be able to get a stand alone inland marine policy. just be aware that it likely will be a surplus lines policy and probably be close to a $1,000 a year as a stand alone risk....

I have mine setup with flat face 3/8' couplers never have had issues with hooking them not sure a single point lever would really save any time to speak of you have to wipe off the face no matter what you use just to help keep the fluid clean.

It just occurred to me, why not connect that fuel injector overflow rail barb to the barb on the front of the pump which sees lift pump pressure? It would be the same as going back to the tank, right? Or even just tee it into the fuel line just before the engine? Because going to the tank it's...

Just a couple of things from my experience in Michigan. My barn has 2 doors 1 is a normal 9*7 car door the other 12*14 for the truck a LX ROPs will not fit the car for without folding the ROPs. My old B7510 would go in either door. 2). MMM mower decks are a PITA if you are doing dirt work...

I have a 250' asphalt drive that I plow with a steel edge back blade. Agree the trick is to shorten the top link so the blade is leaning forward ( assuming you plow like I do driving Forward) if the snow is more than about 8" I will set the bucket about 4" off the drive to Cut the top layer...

Mid-Michigan I own the tank pre-buy 1.879 for 23-24 I use propane for heat, water heat and the dryer 800 gallons a year average.

All you dealer they sold me mine on the LX for$15 as long as I was willing to get it on a thumb drive. Printed it was 3 weeks and $200 something.

Well that is true. The last few times I have rented a stump grinder. The teeth have been worn out. That just make the job twice as hard. I've hired out getting them ground and that's an option with I have 30 or so stumps that need grinding. But it's expensive to have just 1 or 2 done. Yes the...

Just my $0.02 If all your doing with the backhoe is digging out stumps. Consider getting the Woodland Mills WG-24 stump grinder. I use mine with me LX2610 and it works great also takes less room to store.

Best suggestion is to go to a dealer and sit on and drive both around the lot. I got the LX2610 because it would run everything I need including the stump grinder. With the added bonus of not exhaust aftertreatment (DPF). But with the weight of the backhoe you might find it to be underpowered...