Search results

So far the only thing I have found is for the B7100 pto rpm never use the 2 and 3 speeds except when specified by the implement instructions B 40 C ??

Thank you still looking for the rpm speed for the tiller. The engine trans manual for the B7100 manual says never use pto speed 2 and 3 except when following the implement instructions. Still looking for that one.

Sorry dave I have an older cub cadet tiller with its own motor was looking for 00 gear oil for it. no one understood or could not find it. It is almost grease but still classified and gear oil Thank you for the response. Going to try the 540 and see how that goes.

Thank you drain plugs on the two rear axle covers and will look for that third one on the mid take off case. that may be covered by the main support beam for the front plow it has a full lower support from the rear case to the plow. Thank you for the information and for pointing me to the...

Found this old girl and brought her home. I asked the fellow selling it the operating speed of the tiller. Why sure he raises the tiller and runs it in all three speeds. I would like to know what operating speed the factory set for the tiller if anyone has one. The oil in the gearbox...

I had the smaller red knob on my 7000 I just put silicone on the knob and boot and pulled it over Now this 7100 has a larger know that does not turn may try that again.

This old girl is like me run hard and put away wet too many times Had to take the side screen off to change the over size aftermarket oil filter. the brace on the muffler bots rusted bad it has been on there a while. same with the fuel filter bowl and air cleaner marked 08 01?

Yes I can still remember those young and dumb days of life. Now I too am older now seeing what I purchased and knew the problem you can understand the rest. May not have gotten a ham for a hot dog this time. lol

Yes I can remember the young and dumb part of life and like you older now.

I thank everyone for the information. Why someone would not spend $5 dollars to prevent this is beyond me. Just worried about the bearing; do not know how long they left this go but will say it is to the top of the dipstick pull that out and it overlows sitting not running. Joe

Broken shift boot left go over the winter. Dummy found the tractor and brought it home. Ideas for removing and flushing the hyd system Shift boot ordered. Was thinking of draining the fluid and heating it till the water evaporates and using that fluid to flush the system New boot and screen...

Call or look up yourself Joe

I just used spacers to mount my Cub Cadet rear weight bracket on the front of my B7000 It will hold 5 john deer or Cub Cadet weights. It does not look great but works great. No banging or slipping.

Had a stainless steel rod from another project just bent both ends drilled for cotter pin at the valve cover and good to go. Thank all

After you fill the steering box with oil use teflon plumbers tape on the threads of the plug. It will help prevent water in the box. Also keep the small hole in the steering column tube open. It is just above where the tube joins the box. check the top seal under the steering wheel for play...

Thank everyone for the reply's and answers. Looks like if I am going to use the back blade for snow this year. Will invest in a couple of add on eyes to put on the three point cross bar

Will the B7100 hold at the height you set it with weight on it or slowly sink? The B7000 I have been using the mower without the chains. and sometimes have to bump it up. This year put on chains.

I tried to rebuild by B7000 box the parts were totally wrong eve though they were listed as the B7000. I found a good B7100 steering box with the pitman arm and steering wheel. It fit right up. AFTER i cut off the bracket for the dash panel and re welded it at the right height. the nut on...

Anyone know the lift capacity for the B7000?? I do know that the Woods mower RM400 uses two chains to keep the front of the mower and the three point arms locked to height. From that I take it the hydraulic pump will not keep the arms locked at height with the mower weight on the arms?? The...