Search results

  1. C

    Contemplating B2650 purchase

    Ha ha. I dont think I can convince the wife that I need a cab on the 2650 out here in San Diego. It would be nice to have the AC in the summer. Looks like an open cab is in my future. I went to the dealership yesterday and test drove the 3350, nice machine, way different than my little...
  2. C

    Contemplating B2650 purchase

    Thanks for the input gentlemen! It is a very tuff decision. Want to make sure to make the correct one.
  3. C

    Contemplating B2650 purchase

    Looking for a new tractor. I have a B7200 now but it lacks the power I need for doing work around our 12 acre parcel. I only really maintain about 6 acres, mostly bush hogging, landscape work, building things, moving things around, road maintenance, and the like. We have some hilly spots and...
  4. C

    B7200 Hydraulics Questions

    I have the same model, its a little workhorse. 1. The issue i had with my 3PH was that the o-ring and back up ring on the lift piston were worn flat. This caused leak down of the 3PH. It was an easy fix. Removed the seat and related brackets on top of the lift piston assembly, removed the...
  5. C

    Dpf on B3350

    What was the price difference from the B 3350 to the B 2650? Does the B 2650 have any type of emissions controls?
  6. C

    What do you use for a welder?

    Miller 212 autoset, love it.
  7. C

    Dpf on B3350

    I am questioning the same thing myself. I went and looked at the B 3350 on Friday and am curious how the DPF will hold up over time. I am thinking I might just go for the smaller tractor and avoid the DPF. I think the smaller B series will still operate 5 foot implements? It is my understanding...
  8. C

    B2650 price check

    How much more was the 3350?
  9. C

    New B2920 Owner

    Wow, seems to be a great price. I have priced the 2920 through the kubota website and with FEL comes out to about 19k msrp.
  10. C

    New B2920 Owner

    I have been looking at B2920s too. if you don't mind me asking what did you pay for it?
  11. C

    Millings for a driveway

    I put down 1300 feet of it on my dirt road and rolled it after putting it down. After a few years it hardened back into solid blacktop, well gray top now. My advice is to get the base graded correctly with a crown before putting down the millings. To get a really nice surface put the millings...
  12. C

    B7200 HST has more power in reverse

    Thanks for the reply, yes when I roll off the pedal it does have more power. This issue almost sounds/feels like a high pressure relief valve is weak, i.e. Bypassing too soon.
  13. C

    B7200 HST has more power in reverse

    I was doing some bush hogging with my B7200 HST using a 48" bush hog rotary mower and noted that in some spots going up hill the tractor would lose steam, stop, and whine when I tried to keep going. I then would go in reverse up the same slope and the tractor would make it fine. What gives...
  14. C

    Hydrostatic in-line strainer screens B7100HST

    I have a B7200 and the bolts are 26MM. I was in the same boat, mine were very hard to get off. Cheater bar and some cussing and they came off. Good luck. Nate
  15. C

    Replacement PTO Shaft, Shear Pin Diameter

    Just picked up a SQ48-3 bush hog to go behind my Kubota B7200. The hog has got some miles on her but for $300 I thought I would go for it. Gearbox is tight with no leaks which is a positive. I spent some time working on getting the PTO shaft apart, dried grease had glued the two halves...
  16. C

    B7100 loader (B1630C) issue

    Keep after it. I think what you will find is that your piston o-rings inside your hydraulic cylinders are badly worn and bypassing fluid. That was the case for me.
  17. C

    B7200 FEL Bucket R&R

    Oops, this should go in fabrication.
  18. C

    B7200 FEL Bucket R&R

    Working on getting my B7200 back together. I decided to replace the lower wear points where the FEL arm pins to the bucket. The lower holes were about 1/8" out. I cut some 1.5" x 1.5" x .250" squares and drilled them out. Nice and tight now. Put some chain hooks on too.
  19. C

    1640 Bucket Question

    What is the dowel with cotter pin in the end for? What is the hole in the side of the bucket that lines up with the weld nut for? Doing some R and R to the bucket.
  20. C

    B7100 loader (B1630C) issue

    I just rebuilt the lift and bucket cylinders on my B7200 with 1640 loader. The loader should be identical to what you have only that mine is a quick disconnect model. Here is a parts list for the lift cylinder, it was included in the rebuild kit. The curl/bucket cylinder parts bag did not...