Search results

Something else that MIGHT be happening is if there is any grease in that spot it could be what is freezing. there is a plastic/HDPE/Nylon ring that the chute rotates on. Too much and/or the wrong grease will cause a binding issue and increase the freezing potential. Like others have said, clean...

https://www.colemanequip.com/search/b7304/ https://www.messicks.com/parts/B7304 https://www.messicks.com/parts/B7317

I was finally able to get in touch with the dealer and it was indeed the backhoe/pipe recall. Since I don't have a backhoe, and do not foresee it in my future, case closed.

I am the exact opposite. I would use this everyday, somehow. I am an a$$hole, though!!

Same here. Make me jump through too many screens or put in more info than is needed and I am onto the next site. The YT videos from Neal(sp) are useful, but I fully agree that their online shopping experience is HORRIBLE and shipping is just OUTRAGEOUS!!

I think the LX2610/3350 is the same engine as the B2650/3350. I did mine, B2650 cab model. The hardest part was getting the threaded plug loose. Once that was done it was very easy/simple. I may have watched that video and if it does not say, just get the heater ready to install(pipe...

I have the cab on my B2650. I put a fuse location next to the seat on the same surface/plane as the seat mount.

Compressed air or leaf blower or my 20V blower.

Very disappointing. NE WA. I WANT snow!!!!

Just got a call today about a recall on my tractor, 2650 with cab. I do NOT have a backhoe, never did. Tried calling 3 times and only got voicemail, so not sure if this is the same issue or not. Tractor just turned 5 years and made the last finance payment on it. Quite the coincidence in my mind.

I had the red button pop off, saw it by the cab door and figured I had time to get it later. Well, I guess there is enough movement in the door while running the snowblower to allow it to fall out of the cab. I just ordered 2 of these switches and hope they work like the OP's did.

You could remove all the shear bolts and turn the shaft and see if the noise is there. Add in a shear bolt at a time until the noise returns.

"...At that time they advised reversing the front wheels...." "... It didn't occur to me until later that the increased load on the axle bearings by moving the wheels farther out from the bearing ..." You don't mean right to left, you mean inside to outside, correct? Probably pretty obvious to...

I believe that switch is just to turn on a warning light on the dash indicating parking brake is on. I used that to add extra LED flashing light to make me aware the parking brake is on.

I keep getting this notice and cannot search the site. From what I know, and that's not much, I changed nothing since last visit and from what I can find online my settings are correct. Also not ice a huge amount of ads that I do not remember. Any help is accepted.

Do you have any experience with these causing interference with a radio? I have some that cause interference and have tried both cheap and expensive. I even bought these: https://www.amazon.com/gp/product/B075B5BZRZ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

I backdrag with mine in multiple places. I have a back blade, too, but at times it is better to use the blower. So far I cannot see any harm to the blower, its components or the tractor.

Looks like this is the OP. At first I thought this was a strange idea, but with an explanation it seems like a good idea when done correctly.

The fenders are the easy part. It is the mounting of them that has been the conundrum for me.

On my 2650, 2610 predecessor, all wiring is there and ready to go. Switch wiring was zip tied to the existing front work light wiring, IIRC. Rear plugs are there, although they are Kubota specific. I bought the Kubota switch and it plugs right in. 10MM socket to remove the dash enough to gain...