Search results

I have an LX2610HSDC with R14s and just had it in my attached garage last weekend with the standard 7' door opening. I had to manually open the door, push it up as far as I could and put a Vise-Grip C-Clamp on the track to hold it up. My door frame has the hard plastic seal with the flexible...

The spacers are hub centric and fit very tight on the axle hub and the tractor wheels are very tight to the spacer hub. Here is the only sheet that came with the hubs, for the rears. There was no sheet for the front spacers.

Probably 1/2" of clearance at full crank.

These spacers were purchased from Motorsports Tech and were made for the LX2610.

Today I finally had time to install my BORA 2" wheel spacers. The fronts were easy, Since I had loaded rear tires, I thought the rears would be more difficult than they turned out to be. For the rears, I jacked up one side at a time so the tire just cleared the floor. I removed the two nuts...

Got it. I have a digital dash on my LX2610 and have to switch from engine rpm to pto rpm. Since I don't have anything to run on the rear pto, I don't use that setting. Dealer just said to run mine around 2400 rpm for the front snow blower.

I also cut up a stall mat and attached it to my blade. I ended up with 8 - 6' strips, enought o last me for a while. Haven't had any snow to try ot yet, but thought about running blade backwards until a little snow base was built up.

540rpm with a front snow bower?

Make sure the quick connectors under the fenders are connected properly and not corroded. Check the bulb sockets as well. Sounds like a ground/connection issue.

I have a set of "As New" B2650 covers for sale that I purchased from David. At the time I purchased them, I was planning to buy a B2650, then covid happened. I ended up with an LX2610, so I need to sell these covers to help finance the new style and save someone a few $ over the cost of new...

Since I use my LX2610 for my business, bowing snow, I'm wanting to mount some strobes on my LX2610HSDC's mirrors. Anyone ever break a mirror and see what the inside looks like? It would appear there is plenty of room inside to run wires up and out the top. I have strobes mounted on the rear...

Interesting. The mat I purchased has a psydo diamond plate look, but they are very small and much farther apart that what one visualizes diamond plate.

Thanks for the feedback. This is a new tractor for me and I'm new to "tractoring" LOL. I've done a bit of reading on rear plows, how people use them, on what surfaces with a particular focus on removing snow from gravel Seems the majority either turn the plow "backwards" or they put a piece...

I saw a similar material, "corded" in the middle at Fleet Farm. I considered doubling it up for my plow but planned on buying the mat and stuck with it. I can see how it would great on smaller, lighter plows!

Are those R14s grooved? Might have to try that...

Since we're enjoying a little reprieve from cold weather in Northern WI, I worked on fabricating rubber scrapers for my Land Pride R1572 rear blade today. My company will be doing snow blowing this Winter with my LX2610HSDC set up with a 64" Commercial Snow Blower and the Land Pride RB1572...

My original bolts are not grooved on my LX2980 and as I said, 2/3 of those shown for the OP's blower are NOT grooved. The replacements available from Kubota for my blower are not grooved at all. That is my point. It would appear Kubota has decided the grooved bolts, at least for the...

Can't disagree with your there. If Kubota changed shearbolt design, it would stand to reason the new design, if indeed there is one, would suffice just fine for the OP's blower. Per Messicks site, it shows 3 different 5/16" shear bolts fitting the OP's blower,. One of the 3 shear bolts is...

The replacement shear bolts given to me by the dealer when my snowblower was delivered were not grooved. Looking up the part number for the auger and fan shear bolts for my LX2980 which were found on Messicks' site are not grooved either. Head markings (there are none) on my auger bolt...

Barely made my LX2610 sweat. Pulled my Roll A Dock out of the lake for the season. New to this home and was told dock had not been removed for 13 years under prior owner. Obviously they didn't have a Kubota!