Search results

  1. 06B3030

    What did you do to or on your Kubota today?

    I use a couple heavy straps looped through a chain hooked on my bucket to clean the deck of my zero turn. I just lift the front up, and lock the FEL controls. I mulch with it so it needs to be cleaned every so often.
  2. 06B3030

    Front Winch...

    I loop the line/rope back to the tractor with a snatch block, and connect it to the tow hook on the frame. I'm probably going to fab a "protective bar" of some sort to protect the front of the winch. Probably mount it using the bolts for the front brush guard.
  3. 06B3030

    Front Winch...

    Painted it. I do have a HF powder coating kit and a small toaster oven I've used for small parts. Wish I had a bigger oven!
  4. 06B3030

    Front Winch...

    Thanks...helps when you have the tools!
  5. 06B3030

    Front Winch...

    Just the tractor. Had it sitting in neutral, and pulled it 10' or so. If it doesn't rain today I'll be pulling an engine out of the basement.
  6. 06B3030

    What did you do to or on your Kubota today?

    The LED headlight bulbs are a SIMPLE SWAP! Just twist the locking ring and the bulb comes right out in the socket. Grab the bulb, push in, and turn to remove it. Reverse to install the new LED bulbs.
  7. 06B3030

    Rear Floodlight On A LX2610?

    That's why I mounted it there...if the switch was to fail...it would be an easy fix!!!! :cool:
  8. 06B3030

    Front Winch...

    What you have to make sure clears, is the "bracket" that protects the hydraulic lines. I have about an inch of clearance at it's closest point in the swing. Nothing will move to cause a problem.
  9. 06B3030

    Front Winch...

    I decided to put an electric winch on the front of the tractor. I sold my Jeep that had a winch, which i used to pull equipment out of my basement. I went with a HF 5000# winch, as I don't expect to be pulling anything heavier than 500-600#. First thing was to make a mount for the front of the...
  10. 06B3030

    Rear Floodlight On A LX2610?

    It was very nicely made. There were some comments about the switch quality, but I think it's fine! It fit nicely in a "snap-in" panel I had on the side of the dash. Better than drilling a hole in the dash panel itself. I just have to paint another set of screws black.
  11. 06B3030

    Rear Floodlight On A LX2610?

    The rear work light circuit is fused at 20A in my tractor (B3030). It should be called out in the Owners Manual...
  12. 06B3030

    Rear Floodlight On A LX2610?

    OOPS...the picture at the bottom was with the LED head lights AND the LED spot on the ROPS. The LEDs in the head lights did make a big difference by themselves.
  13. 06B3030

    Front Axle Oil

    THANKS guys!!! That's what I was planning on using...but figured I'd check first!
  14. 06B3030

    Rear Floodlight On A LX2610?

    I just installed these LED headlight bulbs and really happy with them. I also installed a magnetic mount LED Spot and used this Wiring Harness. I tapped into the work light wiring under the right tail light. I cut the connectors, soldered them and used heat shrink tubing with the harness. I...
  15. 06B3030

    Front Axle Oil

    I have a B3030 and planning on changing the front axle oil. The WSM says to use Super UDT, which I have some from when I changed the HST oil, or 80-90 gear oil. Any suggestions as to which would be better??? I leaning towards using the Super UDT, but figured I'd ask what others have used...
  16. 06B3030

    What did you do to or on your Kubota today?

    Finally installed LED headlight bulbs...what a difference!!!!! Also installed a magnetic mount LED work light I had sitting around. When I upgraded to the 40 amp alternator, I ran a harness from the rear worklight wire under the right tail light, with a relay to a switch on the side of the dash...
  17. 06B3030

    2014 Jeep rear bushing swap (a pictorial guide on how to abuse your socket collection)

    Gotta love the HF 20 Ton Press!!!! I have one and it never failed to get the job done. I bought it when I had to rebuild a transfer case in my 91 YJ Renegade. Welded up a bender for it to do some metal fab work. The Jeep was a project vehicle for my son and I to work on. Taught him auto repair...
  18. 06B3030

    What did you do to or on your Kubota today?

    Gotta love those EASY fixes!!!! (y)(y)
  19. 06B3030

    What did you do to or on your Kubota today?

    Really nice job!!!!! Came out beautiful!
  20. 06B3030

    Accidently left parking brake on BX23

    Like everyone else, I've done it a few times in the past. Now it's..."foot on the brake pedals"...then insert key!!!