Search results

Surprised that your tractor did not come with all the cab lights as mine did. I remember asking about them when I ordered it last summer and was told that they were all included. Here is a picture of the wiring from my WSM. Not sure if it will be of any help or not.

I recently installed an aftermarket radio into my new LX2610. I ordered a Kubota radio harness from amazon and connected it to the appropriate wires on the radio. To identify the connections in the tractor plug I just used a meter. I did this initially using the amazon harness plugged into...

I would think that even if you were able to find a short enough cylinder with a 4" to 5" stroke you are still into some fabrication to make it work. Your only option otherwise would be to purchase the OEM Kubota parts.

Is this a new install? I have the same setup and have no issues. This shaft is telescoping and should extend far enough to slide on to the tractor spline. The spring loaded coupling can be a pita but doable.

That is correct. In my case the noise made by the removal of the load on the universal joint greatly changed the sound.

Last time my B7200 squeaked it was the rear universal on the driveshaft for the front axle (4WD). If it in 4WD, turn it off and see if the noise changes.

This is the same as is done in cars these days but is automatic when turned to defrost mode. Heat and A/C on at the same time. They used to have ambient stats back in the day that kept the A/C off below a certain temperature and defrost was heat only. Use to destroy compressor seals as they...

Over the last few years I had to replace the seals in both the front hubs on my B7200 that is similar in design. I am sure one was damaged from excessive weight on the front end when one day I was bush hogging and saw a rock in the field that my tenant had unearthed with his plough. The closer...

Your lifting arms are the same as what is on the mmm that I had on the b7200. Max height would be had when the mower is raised to maximum height and wheels are off the ground. Lifting arms can be adjusted until the mower is hitting bottom of tractor when in the raised position. I understand...

Glad it was caught in time. I had this when I was around 18. Went to my doctor who said to keep an eye on it and see him again if the pain got worse. My father was not happy and was able to get an appointment with another doctor in another town. That doctor said it was not serious enough to...

This is how I hung the deck from the B7200.

No real parts list. Bought the 12-volt linear motor from Amazon. The upright rod holding the wire is just a 3/8" treaded rod with some 3/8" fuel line over it and topped off with a rubber cap that I found. I was going to use straight rod and paint it but I did not have any. It is mounted to a...

Here is the actuator I installed on my new blower. Actuator has a 4" stroke. Installed dpdt ctr. off switch on dash to operate and fabbed up mounts etc from misc. junk. Have under $100 in it.

On my 1985 B7200 I would have to have the glow plugs activated until the dash indicator glowed red even in the summer if started for the first time with engine at ambient temp. Years ago when stored in an unheated shop it always started in the coldest winter days without a block heater or...

Dusty, I totally agree with everything that you have stated to diagnose this issue. Just trying to imagine what other forces might be causing the rear half of the coupling to not properly engage the front half and cause wear. I just can't understand the logic in having a metal-on-metal contact...

This set up is certainly not the way that I would design it. This coupling design is basically steel on steel. I wonder why they could not have just put in a longer drive shaft and attach it directly with a connection to a spline on the gear reducer. A telescoping driveshaft with universal on...

That is correct. The angle of the blower has no effect on this coupling. The front blower assembly is solidly fastened to the assembly that contains the coupling. These two components are then raised and lowered as a single unit via the hydraulic cylinders. The universal joint on the shaft...

Will be seeing my dealer in the new year and will discuss this with them. When I was ordering mine in the fall he expressed a dislike of the k member system.

I ran mine last week for the first time after the major snow storm. Lots of areas of heavy snow on my 4000 foot driveway. I engaged the pto at idle and operated at around 2200 rpm. Everything operated smoothly with no vibration or strange noises. These connection points are held together by...

Very strange considering the amount used. I will ask my dealer if they are aware of any issues with this setup. I assembled my blower in October and if this is an issue I will order a spare coupling for after the warranty is over.