Search results

Roger that! water will super heat oil as it mixes and becomes steam as it evaporates out the case breather. Good Point Captain!!!!!! This may be the true problem because water will be mixed under load ( whipped in the oil ) and then try to excape from the heated iron because its not under a...

This shouldn't be happening this is a 2000-2004 gear unit with the throttle petal thats mechanical. Steve are you sure you put all the cluster wires back in polarity with your 12 volt system? In other words are the connectors under the right lug and snapped into place when you repaired the...

Wow that's no good it sounds like a relay frying. Does any body have a wiring diagram to help out here? Steven be sure to check the starter at the solenoid with a remote push button switch to see if the current is there and the starter cranks without the key switch. This way you are ruling out...

Also look at tractorbynet.com, tractor house, and google your need to the World Wide Web. You will find one, they out there W. ;)

It's hard to say where its made because even Parker-Haflin is using Chinese foundries to produce valve bodies, pumps, hose fittings, etc., not because its cheap labor like the unions want to bestow, but because of the USA's EPA rules and regulations of heavy metal waste products that China...

Okay gino what's your serial number please and I will try to help on this one. Make sure the brake is set, the arms are all the way out, PTO is off and your are firmly in the seat. Turn your key to to preheat condition ( igntion pole 1 ) listen for the fuel pump klick as your preheat light goes...

Wildfire I can't get my diagram to upload at 697 KB. I've tried to reduce it but to no avail. If you know how to size your prints ( format ) say a 11 x 8.5 page into the allowable site restrictions please send me a personal Email. :)

Sono... in all sincerity the only way you can measure true temperature of your HST is to shoot the case at the output shaft bearing with a IR heat gun and record the readings before a normal load ( warmed up at least 20 minutes under no load ) and after a heavy load and do the precentage of...

Roy just put your voltmeter on the battery terminals with the engine RPM at half throttle and see if you don't have 13.2 volts on the battery. If 12.8 or greater your generator is okay. If you feel there is a parasitic draw on the battery remove the negative battery cable from the battery pole...

Yes I sent you a private message to your profile address and open up your home page and see if it made it. If not let me know and we will Email....

Wildfire I don't know if this will help or not schematics never look like the real thing but I think Vic is right their simply auxillary ports for power beyond applications. I'll try to get my hand on a BX2200 hydraulic diagram specific to this model. I knew Kubota made these tugs but didn't...

:eek: Mike look for a private Email at your home page we are going to fix this now. You need to make hay!

Wildfire.... plugs!!!!! just kiding. Are the holes open into the hydrostat? Picture two shows a cross drill hole in the treads which suggest to me a case drain for pressure port. I own a BX2230 and I will get my manual out and see what the hydraulic schematic shows for Aux circuit for attachment...

Welcome Mr. Roy...:) Here's a thought... put it all back together and use a remote push button switch across the starter solenoid and the positive battery terminating on the starter. See if it cranks, since you have bench tested the starter you need to put it back in the circuit. The issue is...

Do you have your Works Shop Manual? If so look for all the return springs on the linkage and make sure they are center in parallel to the stays and that there is no grass hanging on the ball joints where the linkage changes direction. You can dsconnect the petal linkage at the bell crank and see...

rorc is this a two cylinder diesel engine? If so I suspect your injectors need serviced. I'm not at all familar with your B1400 but when fuel fills the crankcase this or oring seals on the injectors are the only way diesel fuel can get in the crankcase. Also check your fuel tank to see if the...

Crawlerchris welcome aboard .... how many hours on your meter and have you greased the linkage? If you have and the rods are free its a simple adjustment but the HST L- series will drift but you pulling the petal back tells me it's in the linkage particularly the bell crank where the petal...

Dusty I wouldn't shockload the clutch in an attempt to break it loose. I'm not familar with this B-series but isn't there an inspection cover on the right side of the clutch housing? If its rusted to heck in there, I'd WD40 it in place and see if the pressure plate backs off and just let her...

Dusty I wouldn't shockload the clutch in an attempt to break it loose. I'm not familar with this B-series but isn't there an inspection cover on the right side of the clutch housing? If its rusted to heck in there, I'd WD40 it in place and see if the pressure plate backs off and just let her...

Man they really decked the block and the heads look good too, this should be a tight rebuild Aqua. Did you resize the rods?