Search results

I’d be looking for a wiring or grounding issue. Is it likely that your temp gauge quitting working was when your fuse blew? If so, check out the wiring downstream of your blown fuse. It could be a bad ground also. It could also be that your charging system quit working and your battery drained...

Very sorry to hear this Mike. Our deepest sympathies to you and your family.

I looked under the tractor and there was a little seepage from that weep plug. I pushed the plunger up for a while and nothing dripped out, but theres definitely a little oil around the area. I havnt noticed any on the ground where its parked either.

Good news today! I went over there and my son drove there as well. We went through everything and switched couplers around to see what we could figure out. It boiled down to tge valve so we pulled the rear wheel and the cover from the inner fender to have a look. It turned out the bolt holding...

Thank you for that detailed description Dan. One thought and question thats nagging me though, is could it be possible the inner seal on one lift cylinder has blown out and creating the back pressure? When I first encountered the problem a couple weeks ago, it would lift very slowly at full...

And yes Dan, the loader on the ground is the only way I can get the couplers off. The pressure really binds them up. I have to move the joystick back and forth many times with the engine off to relieve that.

I’ll give that a try next time out there. I wish it was closer, but its an hour away, and a kubota dealer for parts is another hour. I dont get there all that often.

By tracing the lines to the lift arm ram I figured the blue and red ran the lift arms so swapped the blue with white and the red with yellow. It transferred the lift function to the curl positions on the joystick, but like I said, it reversed the issue. Instead of no lift, now it had no lower.

Ok, I will try to get those identified. Meanwhile a couple questions until I get there again with a new coupler. Both ways I tried, the lift rams problem simply reversed from not lifting to not lowering. Im not real experienced with hydraulic repair, but it has me wondering if its in the valve...

I got here today and those couplers sure came apart hard. No rust or anything, just very dry I imagine. Theyre oiled up now. The four lines with couplers are situated in a square pattern and are color coded. Blue at 10 oclock White at 2 oclock Yellow at 4 oclock and Red at 8 oclock. I first...

Theres a blower on the 3-point and that goes up and down fine. It doesnt seem to matter whether thats in the up or the down position, the loader acts the same.

Thank you Sir, I will give those recomendations a go, next time I get over that way. It may be 2 weeks before Im able. I will report back on the results.

I went to use the L3240 a couple days ago. The loader lift rams would not raise but would go down easily, like in float. The bucket tilt rams functioned fine. The last time I had used it, about 3-4 weeks ago, the lift had seemed slow. i checked the hydraulic oil and added 2 gallons super udt...

Kubota L8304 New in the kubota cellophane packaging with the label. This fits a few different models, usually for 2nd position. It has the float detent. If you need pictures let me know, theres not much to see unless I unpackage it, which I wont do just for tire kickers. $165 shipped. Paypal or...

One genuine Kubota dynamo part # 15531-64017 New in Kubota factory packaging. $125 shipped.

Also, asking and selling prices arent usually that much different. Sure theres a diference between wholesale and retail, maybe 25% at most. You mention a “freind” is offering this to you. Take your freind to a dealer that you both know, sit down and ask him what the right price would be. Theyd...

Id just say that original selling price has much less to do with its value than its present condition and what comparables are priced at. I see jd tractors such as 4020’s that consistently sell for much more than they sold for new back in the late 60’s. And thats having thousands of hours.

Im unsure, but Leylands were blue and go way back

Flip, funny that you would say that your bio-mass heater is a loser compared to propane. Every farmer I know who uses one feeds all corn through theirs. Main reason being the corn is FREE to them. Every dime spent on land costs, seed, fertilizer, fuel to harvest, and right on down the line is...