What did you do to or on your Kubota today?

[OrangeKrush]

Yesterdays project with the wife any takes on where we found this View attachment 53059 ?

Fuel tank? Only takes a second for one to float in while you have the cap off and not watching.

 

[Ikc1990]

And hours and a nightmare later you get it removed.

 

[River19]

Got another 2" dusting on top of the couple we had earlier this week.......that is kinda the normal way things go in NH/VT.....get a storm people notice, then get a number of 1-3" dustings that need to be cleared otherwise they just turn to ice.

Back bladed things this morning. Still mostly using the non- aggressive side ie. flipped 180 degrees from normal so like ) going in > direction.......

But we always end up with some sheet of rough ice by the garage which allowed me to be more aggressive and use the blade in the "normal" direction and scrape crap into a pile to then hit with the blower.....

Lovely machine for this work. Still no issues with my heavy grade with Turf tires.....and the bonus is the tracks I leave behind provide great traction once they freeze up nice......

 

[ctfjr]

Got my LED 1156 and 1157 bulbs in today and swapped all the small bulbs on the tractor. Was a little disappointed to find the heads of the screws on the turn sign fixtures were really rusty. Swapped with some stainless ones I have.

 

[nbryan]

And hours and a nightmare later you get it removed.

Now I'm curious how you fished it out.

 

[Ikc1990]

Now I'm curious how you fished it out.

Well alot of cussing. Alot of learning how to use 3 for wooden dowels as chop sticks with duct tape on end after I drained the tank. Still was better than. My buddy's 70 horse massey Ferguson that we fished a dead mose out of fuel tank. After I tried sucking on fuel line to get sludge out. but this was probably 3 hrs with flash light on cellphone and 2 dowels and persuasive voice telling the leaf it could go anywhere but in that damn tank. Lol we got to know each other pretty well, but still not freinds lol

 

[nbryan]

Well alot of cussing. Alot of learning how to use 3 for wooden dowels as chop sticks with duct tape on end after I drained the tank. Still was better than. My buddy's 70 horse massey Ferguson that we fished a dead mose out of fuel tank. After I tried sucking on fuel line to get sludge out. but this was probably 3 hrs with flash light on cellphone and 2 dowels and persuasive voice telling the leaf it could go anywhere but in that damn tank. Lol we got to know each other pretty well, but still not freinds lol

Ok, phone flashlight with chopsticks and duct tape, a motley crew for tank fishing, but you get 'er done!
That's all that counts, really!

 

[bmblank]

Lol we got to know each other pretty well, but still not freinds lol

Know your friends, but know your enemies better...

 

[NHSleddog]

Still punching holes. We have about 6" of frost now and so far, the auger is working well in it. I have modified another bit to aid punching through.

 

[Ikc1990]

Still punching holes. We have about 6" of frost now and so far, the auger is working well in it. I have modified another bit to aid punching through.

View attachment 53133

Nice looking set up what are you building fence ?

 

[B737]

Rear valves installed in preparation for Top-N-Tilt

 

[Ikc1990]

Rear valves installed in preparation for Top-N-Tilt

Nice job looks factory ! Good job

 

[NHSleddog]

Nice looking set up what are you building fence ?

I have a poker buddy with a fence company. I drill a lot of holes for him.

 

[B737]

I didn’t do it the dealer did I cheated this time. I thought the rear valves were installed above the fender, but apparently the kits go down by the three-point

 

[Bulldog]

Busy today and used both tractors. Put wheat seed out on part of the pasture and part of my hay field. Then switched over and fed cows. After that jumped on my 9000 and pulled the old batwing around for a few hrs. Finally had some of my low ground that was dry enough to get on without rutting it up.

 

[doublebass73]

Put a grab handle on the right hand fender on the L2501. Quick easy job. I also have a telescopic stabilizer kit for the 3 point waiting to go on but that will be another night.

 

[OrangeKrush]

I have a poker buddy with a fence company. I drill a lot of holes for him.

IOU’s ??

 

[NHSleddog]

IOU’s ??

LOL - hardly. My wife is amazed that our core group of players have been playing over 30 years now and some seldom win and some seldom lose. Although my fence buddy can hold his own.

 

[BA76]

Put a grab handle on the right hand fender on the L2501. Quick easy job. I also have a telescopic stabilizer kit for the 3 point waiting to go on but that will be another night.

View attachment 53151

That looks really nice!
Those are some aggressive tire chains. Perfect for ice like we received on the New Years weekend.

 

[bmblank]

Put a grab handle on the right hand fender on the L2501. Quick easy job. I also have a telescopic stabilizer kit for the 3 point waiting to go on but that will be another night.

View attachment 53151

What handle is that? I want to put one on my L3901. I can't believe they leave it off. I mean, I'm pretty happy with what I paid for my tractor, but come on, I would have been willing to pay a little extra to have that on there, had I known.