Welder Advice

[#40Fan]

I hate to say this, but I bought a $200 MIG welder off of Amazon that I am amazed with. My Millermatic 221 that has auto set fried its motherboard and I needed a welder faster than I could get the board, so I bought an Arccaptain 165A and had it in hand the next day. 110/220 volt capable, gas or flux core as well as stick welding and has a comparable auto set feature.

I've been so impressed, I still haven't ordered the motherboard for the Miller. The auto set feature on both welders can take a beginner and make them look like someone that knows what they are doing.

 

[PoTreeBoy]

No aluminum, welds would be on carbon and mild steel from 24ga - 1/4" plate for all the stuff I've been putting off. Sounding like a decent 220 mig would give me the best chance at actually succeeding at faking my way through them. I'd still like to end up around $400 though if that's even reasonable.

Here's two mail-order possibilities, they both have everything for stick, MIG and flux, except gas regulator. Harbor Freight

 

[North Idaho Wolfman]

I hate to say this, but I bought a $200 MIG welder off of Amazon that I am amazed with. My Millermatic 221 that has auto set fried its motherboard and I needed a welder faster than I could get the board, so I bought an Arccaptain 165A and had it in hand the next day. 110/220 volt capable, gas or flux core as well as stick welding and has a comparable auto set feature.

I've been so impressed, I still haven't ordered the motherboard for the Miller. The auto set feature on both welders can take a beginner and make them look like someone that knows what they are doing.

I've been seeing Arccaptain Ads all over the place and wondered if anyone other than a Youtube mouth peice had anything good to say about them.

 

[#40Fan]

I've been seeing Arccaptain Ads all over the place and wondered if anyone other than a Youtube mouth peice had anything good to say about them.

I was the same way when I was looking at it. I could have purchased it from the company directly and saved a few $$, but buying from Amazon, I knew I'd have recourse if it turned out to be a pile of junk. Other than it can't weld as long as the Miller could at the highest setting and it didn't come with a regulator, it surprised the hell out of me.

One other draw back....it will only fit the small 2 lb. wire spools. The machine is tiny.

Edited to add: It reverts to flux core after every power cycle. It scared me the first time it did it. Switching it now isn't a big deal.

 

[PoTreeBoy]

I've been seeing Arccaptain Ads all over the place and wondered if anyone other than a Youtube mouth peice had anything good to say about them.

I wouldn't be surprised if a lot of the Chinese machines use components from the same factory. They seem to have the same features. Just a new brand every few years.

I haven't used my yeswelder a bunch, but it still works. I'm not enough of a welder to know, but it seems adequate. One place they save money is the case, they may roll out soup cans. They make improvements periodically, the current 'pro' model supports a spool gun, I think, and has settings for more wire (I'm not a big fan of synergy so far). They've gone to a manly black paint, mine sports baby blue. And mine has a 110 plug on the cord. Which means the adapter is a short cord with a 220 male plug on one end and a 110 female receptacle on the other. Better not plug your grinder into that! I understand they've reversed that on the newer rev's.

I looked at Miller, Lincoln, Hobart and ESAB. They make some fine machines, most likely better controls since they're designed by real welding companies. But for this hacker, I couldn't/wouldn't pay the price. And the multi-function machines are all made in China, I think.

 

[Runs With Scissors]

Hard to add to all the good advice posted above.

My ‘vote' would be for a MIG machine for sure.

There seems to be a smaller learning curve for MIG Vs. TIG.


I will just add that my “personal experience” with Thermal Arc was/has been stellar.

Not sure if they make MIG machines or not though.

I wanted a Miller Dynasty, but like the saying goes “Want in one hand, and sh1t in the other, and see which one fills up first” applied here.

I can’t recall exactly when I bought it, but it must have been nearly 15-20 years ago.

Got lots of hours out of it so far.



EDIT; I also agree with the “practice, practice, practice” idea.

And I really like watching this guy the “Weld Monger” ..(Jodie?)

I like the fact that he tends to cut his welds open, to show how well (or not) his welds were.

 

[Yooper]

For the price point I would recommend you eliminate tig. Tig welding is a whole ‘nother animal to get good at and it is very unforgiving! All the advice so far has been good.

I have never welded with a 110 machine but with the latest inverter technology I guess I wouldn’t be shocked if they would suffice for 1/4” mild steel. The duty cycle would be my main concern.

 

[unhdsm]

My Eastwood 180 Mig has been good to me. They have them right now refurbished from the factory for $350. My neighbor bought a entry level 110v from Tractor Supply and ends up using mine because his 110V isn't hot enough. If you want 110V you have to get one of the better brands, which ends up being more than the Eastwood 180. I'm in Northern New England too and I would also recommend an intro class at a tech school. I paid $500 and it was well worth it for 6 classes.

 

[Old Machinist]

For the price point I would recommend you eliminate tig. Tig welding is a whole ‘nother animal to get good at and it is very unforgiving! All the advice so far has been good.

I have never welded with a 110 machine but with the latest inverter technology I guess I wouldn’t be shocked if they would suffice for 1/4” mild steel. The duty cycle would be my main concern.

I welded with a 120v Lincoln for 40 years and defended it's capabilities. I DID put in a dedicated 25 amp service for it. What you will find when you read is you can't get full power out of a 110v unit on a standard 15 amp household circuit.

By the time you add a dedicated circuit you might as well go 240v at the appropriate amperage for the machine and be done with it. I have been much happier with my mig since I went that route.