Search results

You can get most the parts from messicks, but as the moderator suggests, send it out unless you have the proper tools to do the job correctly. I highly recommend this company they are local to me but do work from all over the us. they rebuilt my injectors and I had 2 friends have the...

Just as an FYI a RC48-G20 will also fit your mower. I have a G5200 that the previous owner installed one on and the only difference was the link arms had extenders on them. works flawlessly.

So, the WSM is not the greatest it does not show how to install the hydraulic control valve. below are the diagrams of how the pipes are run normally, tomorrow when it is light out I will take pictures the best I can to show how my lines are run to the lift cylinder.

No Problem, glad to be a help. Just as an fyi incase you have not seen it yet someone posted the WSM for this tractor in the forum. Download it before it goes away. the part number for the hydraulic lift it is Kubota #79840-31130 CYLINDER, ASSYl they do not sell it anymore you will need...

In all your pictures i do not see your aux control valve. Where is that? The hydraulic with the screen attaches into the bottom of the pump. The aux feed lines come off the top of the pump. Tomorrow I will look at my workshop service manual to see if they have instructions on how to install...

If you have replaced all those parts and you can hear bubbling when it is running, it sounds like you water pump is bad. Pull the thermostat out, disconnect the upper radiator hose have someone hold it into a clean bucket start the tractor and see if coolant flows, if not replace your pump...

I am assuming you are talking about a snow plow or pushing blade if so here are the models. if you are referring to a rear plow. I do not know those numbers. 46" Blade - Kubota G2003 front-mount 48" Blade - Kubota G2000 front-mount

Bull from my understanding the D600 was used on a quite a few zero turn mowers, one example is the Grasshpper model 718.

I used PB blaster soaked for 2 days sprayed multiple times each day they I ended up using a gear puller a small one. pulled right off.

that plow frame mounts to your mower linkage. the two link arms that drop down from the frame. If you look up the front mount snowblower for the G6200 it is a 2 stage blower model G2546A the sub frame is 007000 SNOWBLOWER SUBFRAME AND QUICK HITC Messick has the parts diagram for you. but...

G5200 and G2500 snowblower mod. After one whole season of blowing snow with my new set up. I was having issues with the fiber shaft coupler breaking. I went through many different couplers, I fabricated a few from sheet metal they did not last long. I used a VW beetle steering shaft coupler...

Nice job, It is do nice having the knowledge and tools to fabricate and repurpose. From previous exp. don't use the plow with the deck on. if you are moving dirt you will most likely get stuck.

Not sure if this will work on our machines for the hydro units. But I pulled one of the hydro couplers off an old JD 140 you know the green machines. Attached is a picture. I used it to replace the fiber disk on my G2500 snowblower that kept braking. It runs smoother than ever when the...

You will have to post some pictures. They are great machines, I love mine and use it for snowblowing in the winter also. It works great.

from all my knowledge and experience with this mower, if you purchase mulching blades and you can get Gator style Oregon blades Oregon mulching blades are part number 391-617, you will have to bore out the hole if the spindles are the same size as the RC48-G20 decks. They work great. I would...

Last year after using my g2500 snowblower I realized that I hated the short and wide chute. when I blew powder it was like being in a blizzard. Also when you got into deep snow you could not blow it since the chute was so short. This summer I took a chute off a scrap Ariens 1028 that I found...

Smokeless, I hope you have found a deck. but if you have not and for others the mower decks for the G3200, G4200, G5200 and G6200 will all fit each model. Replacement decks that you can get are any deck for those 4 tractors ( These are not available anymore) you will have to find a used one and...

So I finally got to try my new to me tractor on some decent snow. We got 24" Worked great. I am going to add a few mods, I am going to extend the chute and add drift cutters to the sides.

Snowblower Modification and upgrade. Parts used ADTH landing gear motor for RV 12v DC 30amp part number 1RV-200 (Way overkill, I had one left over from my old 5th wheel trailer) ($170-320) Very expensive and not needed, you can easily purchase a windshield wiper motor to do the same thing and...

I have always liked the old Garden Tractors, and I am a little OCD when it comes to my equipment and vehicles. but one thing I can tell you is that since I bought mine I have met a quite a few people who I bought parts off and they sold theirs and regretted getting rid of it. It took some time...