Search results

ZB600 engines were used in Carrier Silver Hawk reefer units. I would think parts, manuals, etc could be bought at a Carrier Transicold dealer. I believe Trane also used them. See you are in BC. Vancouver has a number of Transicold dealers.

My BX 2660 idled around 1400 rpm. I set it lower to 1300 rpm. Any lower and it runs rough.

All new fuel, lines, tank, pump and filters. Fuel is left over from winter and has Lucas anti gel in it. So I figure the fuel system is covered. Sorry I should have mentioned that. Maybe a cetane boost and injector cleaner? Thanks Jim

D600 sat for many years (one outside). It is a 1800 RPM (I think) engine out of a reefer. Engine would turn over easily with wrench on crank. When I drained the oil, it had several cups of clear water in it. I assume rain water, because stack is pointed up and had a plastic bag stuck in it...

Kubota man No .......... It is I, that apologize for hijacking your thread with a rant. You asked type of oil and not brand. The Amsoil commercial just rubbed me wrong way this time. Again I apologize.

Thank God this was about Amsoil and not religion or politics. I can't even imagine of the length of your reply then. I never tried Amsoil nor would I know the difference! Much less care. The End

A man born blind can feel the warmth of the sun on his face. BTW If you never had Timmies, maybe you just shouldn't express your opinion about it or mention the fact, that you just hate doughnuts. Why would I use uncertified oil? Just because you said it is great stuff and sell it? Save...

eserv By the time the Amsoil sales pitch is done, I feel like I need a shower. Do they send these guys to Amyway sales school? It maybe a great product, but if I want to hear ALL about it again ............... I'll ask.

JWATT51 Nice job. I'm thinking of trying that out. Would mounting it upside down help with preventing moisture entering the actuator? Does the bracket only have one bolt in it so it pivots? Was looking to do something hyd like this, but the actuator would be less expensive. The valve and...

Brian Here is how a fellow did with an actuator. Looks good, but I wonder how it will hold up in the cold, ice and moisture.

Mud I get QD from Discount Hydraulic Hose. There is a quick disconnect size chart. Near the top of the page (4th line down) is a link to a PDF. Hope it is helpful. Jim

If the tractor won't shut off, because of fuel shut off problem, use the fuel shut off lever on the injector pump. There are two levers on the pump. One is connected to the throttle and the other is hooked up to nothing. That is the shut off lever. Just push the lever and the engine will...

Mud I've been getting quick disconnects and fitting from discount hydraulic hose . QD's for my BX2660 are this type. Hope this helps. Jim

Great! If looking for a new cyl try: surplus center

Messick's will email a link to a PDf of the parts.

You have a different valve, but that was my problem. I have one DA cyl to angle the blade and it only went in one direction. If I reversed the two lines, it worked the opposite direction. Seems to me, that if you have two SA cyls, it should work. Pressure to one cyl should empty the opposite...

Push stick hard to the right. You will feel a detent click. Then it will work both ways. Had the same problem. Jim

The thread on the adapter is 10mm X 1.25mm. Just checked my D600 and got psi of 420, 420 and 380. Checked glow plugs and all heat up red. Will try to start again, but previous attempts it was very hard to get running. Had it running one day for about 10 min. Hasn't run in 15 yrs. Valve...

Really interesting thread and a great job Dusty. Love the lights. Your not going to trash them without tearing up the fender. :D

Here are a few better pics of the solenoids on the intake side. If the top one kills the engine, would I need the fuel shut off solenoid on the front of the pump?