Search results

  1. W

    Thread tape, thread sealant, or ????

    Not so sure if I should be concerned about splitting the female port, as all of these fittings are male polypropylene fittings.......tightening into female cast aluminum housing.
  2. W

    Thread tape, thread sealant, or ????

    i'm replacing my original Teejet Control Valve AA17L with a new one, and concerned about the best product to use for attaching the green leaf fittings. I was about to purchase the Blue Monster Thread Seal Tape, but just not sure if that's what is needed. I need to make sure I use the correct...
  3. W

    Diesel Additives - Time to Change Brands?

    After reviewing this video, I noticed the comparison included, PowerService Kleen * Cetane Boost, Archoil AR6500, and Hot Shot Secret EDT....... all without Anti-Gel!!!! Not an apples to apples comparison in my opinion.
  4. W

    Diesel Additives - Time to Change Brands?

    I recently ran across this YouTube comparing five different diesel additives. It's kinda lengthy but if you skip near the 39 second mark, you'll find the summary. After viewing the video, I'm thinking of changing from Power Service to Opti-lube XPD. Anyone using Opti-lube.......please share...
  5. W

    What is the best way to remove the front wheel/tire when repairing a flat?

    I like your method of loosen the lug nuts, drive, etc. Also reminds me I need to touch up the rim.......great advice.......thanks!!
  6. W

    What is the best way to remove the front wheel/tire when repairing a flat?

    I called out a mobil service to repair a flat on the front wheel/tire, and was shocked when he took out his sledge hammer and began to beat (with major force) on the inside of the wheel/tire to remove it. This process took about four attempts. I could only wonder what damage could occur to the...
  7. W

    Need Recommendation For Air Compressor

    My old Campbell Hausfeld is on it's last leg, and searching online leaves me with more questions than answers. My primary uses are keeping the proper air pressure in the tractor tires and other vehicles, impact driver, etc. I prefer a 110V unit. Your thoughts, recommendations, and suggestions...
  8. W

    rotary cutter question, please

    I have had good luck using this one from Harbor Freight........ https://www.harborfreight.com/multi-use-transfer-pump-63144.html
  9. W

    trash bin carriers

    Another take on trash bin carriers........my objective was to have something simple (easy hook up), and that was always available to get the trash bin to the pick up point. This set up serves a couple of needs: 1) basket for the wife's landscape projects, plus the basket is also used for a...
  10. W

    Carbon Canister and evap. system on Gas RTV?

    Not a RTV, but same dilemma on a Scag Zero Turn. I didn't realize it had a set of charcoal canisters until after the purchase, and then to learn the down side of having them.........i.e. being careful to not over fill the tank, using a hoist to raise the mower to clean the deck, mowing slopes...
  11. W

    Tractor PTO Sensor Plug

    As stated earlier probably a Yazaki brand. Here is a link to their Complete Catalog.......with an excellent catalog search feature. https://apps.us.yazaki.com/ComponentCatalog/
  12. W

    Thanks for the quick response.

    Thanks for the quick response.
  13. W

    Quick question on the Cat 1, Euro hooks. I have all my equipment set up with 7/8" lower link...

    Quick question on the Cat 1, Euro hooks. I have all my equipment set up with 7/8" lower link pins (each runs between U bracket). If I converted my set up to the Cat 1 Euro hooks, is this all I need? I don't want to get into any type of additional plates, flanges, etc. Thanks a million for...
  14. W

    Best method to remove top plate of gear box on Woods rotary cutter?

    Jay, sounds like the finishing touch to get that top removed.......thanks!!
  15. W

    Best method to remove top plate of gear box on Woods rotary cutter?

    Russell.....sounds like a plan.......I'll give it a try.
  16. W

    Best method to remove top plate of gear box on Woods rotary cutter?

    Yes gear oil.........not grease......sorry for the mispost!!
  17. W

    Best method to remove top plate of gear box on Woods rotary cutter?

    I need to change the grease in the gear box..........It seems most recommend method is siphoning out the grease thru either the fill opening or the level fill opening. Some even recommend tilting the cutter on it's side.........not doable for me!! My preference would be to have more access for...
  18. W

    HST fluid change - Perhaps an easier way to refill?

    Purchased from Amazon: WirthCo 32410 Funnel King 1" Thread Polyethylene Drum Funnel - 3 Quart Capacity, 1” Thread