Search results

Take the negative terminal off the battery for 15 minutes. With the battery charged (make sure it's full with a charger) reattach. Disconnecting power from the tractor's circuits will reset them, or should. I do it with my car sometimes helps clear a stray check engine light. Sent from my Moto...

The quick coupler on the front loader is referred to as an SSQA - for Skid Steer Quick Attach. So yes, any standard ssqa implement should work. Sent from my Moto G (5) Plus using Tapatalk

On my B2650 the lower link pin shaft on the tractor has a centered "set bolt" that I loosen just enough for play to get the lower link arm to slide on between the shaft end and BH sub-frame. Usually one link pivot will slip on without loosening the set bolt but not the other. Need like 1-2 mm...

Actually a good idea I may use sometime. Thanks! Sent from my Moto G (5) Plus using Tapatalk

Should work but suggest putting on the die bit backwards so the cutting side faces the cut end when removing. Sent from my Moto G (5) Plus using Tapatalk

I never meant to suggest don't follow the manual service intervals, DO! I'm following it strictly for my tractor! Just a lot of suggestions out there to change all your hydraulic oil, too, at 50 and/or 200 hours. I took those suggestions seriously, that's why I brought it up with my service...

Others have gone through lots of trouble with shop vacs etc trying to keep hydraulic oil in the machine while changing oil filters. My hydraulic fluid level was full when I changed the HST (transmission) and hydraulic oil filters, and the HST filter hardly lost any oil when I swapped it. But...

Change the engine oil if you have the correct oil, and a Kubota engine oil filter. The only other items needed at 50 hrs are to change the transmission (HST) filter and hydraulic oil filter. And grease/lube the machine etc. Sent from my Moto G (5) Plus using Tapatalk

There's a 50 hour then 200 hour main items maintenance schedule. Subtract the 25 hours from the readout for those two intervals, then don't worry about the difference after that. The next main items (hydraulic and hst filters, hydraulic oil, engine oil and filter changes) are done at 400 hours...

Did you try backing up the hill?

This is how I use the clip when BH is off. This pic has the BH still attached as I'm not removing it just for a photo, just routed the hose to demonstrate. Sent from my Moto G (5) Plus using Tapatalk

My B2650 with BH77 backhoe has the hose held up out of the way with a clip Kubota mounted for the job on the rops right side just above the hydraulic connector to the tractor. I loop it around the rops upright and through the clip when BH is off and it's well out of the way for 3pt operations...

If you go front mount get the 63", not 51". As you can see in my video this tractor has plenty enough power for it. Sent from my Moto G (5) Plus using Tapatalk

Online spec sheet for BX23S says weight (with rops) 725 kg (1600 lbs). That would have to exclude the bh and fel, no? My B2650 tractor alone is 1786 lbs. Sent from my Moto G (5) Plus using Tapatalk

That was my neighbor's driveway wanted it cleared before she started using in spring, and mostly grass grown over the gravel. My driveway is solid gravel, and if yours is 3/4 down crushed gravel and level, just set the drag shoes a little lower at least at first snow in season until ground...

I really like our front mount 63" Kubota Blower. With the 60" box blade on the 3pt as ballast (and a useful snow moving tool) get good traction. Here's a link to a video of it in action last winter, clearing a winter's worth of drift compacted snow off the the 1000ft driveway in under an hour...

16" bucket on my BH77, B2650 tractor. Been trenching/digging through our roots and rock laden grounds, working fine. Pulled stumps, moved boulders, works great. Fyi I have a mech thumb too, really handy. Sent from my Moto G (5) Plus using Tapatalk

Not your make, but my WC68 (Woodland Mills) chipper is hydraulic self feed and I love that feature. Branches down to about 1" need to be lopped but any 1" and smaller, on green aspen anyway, will bend into the chute and get pulled through with the trunk. I did some chipping at a neighbor who...

My B2650, bought here in Manitoba, came with a block heater factory installed. The little 3 cylinder takes only an hour to benefit from block heating in -30C weather, starts smoother and less black smoke. Yes I use the glow plugs for 10-20 seconds as well in those conditions. Sent from my Moto...

Add the hydraulic oil filter. There's 2 hydraulic oil filters, transmission (HST) filter and hydraulic oil filter. And the front axle takes way less than 5 gallons UDT oil. It uses 5 US quarts, and you can use way less expensive 80w/90 gear oil in the axle. Why have you decided to replace all...