Search results

So i just picked up my second b6000, except this "new"one comes with the factory 4 way kufd110 blade and controls already mounted. I was going to take off the blade off of the new one, and mount it on my "old" one, however I noticed the hydraulic block where the lines run in on the new b6000 is...

Yes, I have one and use it a lot. Use it when I have topsoil delivered to scoop and dump, dont even have to get off the tractor, used it for gravel, used it to remove gravel.....a cheap attachment I couldn't live without (until i get a tractor with a loader), paid 200$ used for mine

Not positive, but for your gear drive b7100, you are looking for a model#kufd110 for direct bolt on(no mods), otherwise i believe the blades for the hydro 7100s are different.....

3 pictures of a front blade from a b7100hst 2wd that i am interested in buying for my b6000......is this the correct blade for my machine? I have seen pics online of b6000's with front blades and the blades look different than this, the owner cannot find a model#, hoping someone can...

sorry guys, pto reverser is gone should have posted earlier

will try to get pics tomorrow, looked at other side to mirror it, couldnt figure it out.......the threaded rod on the broken side just slips into that piece that goes under tractor to good side, cant figure out how it would fit and stay in there......

As i was driving through my backyard in the 18" of snow i still have in spots, i got the ole' b6000 stuck. As i was trying to get unstuck, i started to turn the steering wheel to try and get those front tires going, in doing so, i heard a snap, and noticed that my front left tie rod had become...

ok, update on how i was successful at doing this incase anyone else is in this situation.....First off, the original adapter i had to go from 10 spline to 6 spline ended up getting too nipped up from getting unstuck so i ordered a new one off of ebay......that adapter did not have the groove on...

http://catalogs.hubcityinc.com/farmrev/PTOproducts.html#1

http://catalogs.hubcityinc.com/farmr...roducts.html#1 found this in another thread as this has been occupying all my time......is this what i need? Which one? Better yet, how about this one from ebay...

Well, i "manned" up, put the gloves on, braced myself, and did the good ole' fashioned way, i brought the shaft with stuck adapter to the power equipment shop...now naturally the end of the adapter is a bit touched up from me trying to get it out, is it still any good? If not, does anyone know...

thanks for the response, when you say roll pin, what exactly is that? Also, is using a hammer to get the pto reducer on the pto of the tractor a wise idea? I have not done it, but very tempted, of course i cant now because the reducer is stuck.....

ok, i just bought a 3pt hitch snowblower built for reverse pto's like my b6000 has....question is, the shaft to the blower doesnt fit up to my pto, it is bigger than the pto on my tractor, luckily for me, i had a "reducer" ( i think thats what it is called) so i tried that, and while it worked...

how come no one said: "hey iddiot, did you check to make sure there was diesel in the tank!" Well i did check it, thats the first thing i checked, i guess i cant even do that right. Filled the tank, cranked it for a few minutes, and there we go. Now, on to order a new starter........(yes...

Hi guys, does anyone know if a model b74a snow blower will fit my b6000? I mostly find it fitting a b6100, b7100, and i only found one source that says it will fit a b6000, i just want to make sure though, thanks, now out to dethaw my gelled diesel fuel!

my b6000 starts all the time, never had a problem. We had some really cold temps over the past week, -10 one night, mostly single digits the others, went to start the old girl to put her to work tonight and she wouldnt start. It turns over, but wont start. If this is gelled fuel, how do i go...

nice setup, will those size turf tires work on my b6000? If so, what size are they????? I have been doing tons of research and it seems as though there is too much math for my raisin sized brain to handle

Thanks for the replies guys, sounds like a job for this weekend, I will let you know how I make out.

Hi guys, I am no mechanic by any means, and, considering that, is there any easy reason as to why my big new (last year) battery is slowly draining on my b6000? I fired it up last weekend, and I could tell it wasn't all there, and then this weekend I had to jump it to get it going. When i turn...

have hub city pto reverser for b6000. Will trade for complete front blade setup for b6000 or sell for cash. Make offer. Can send pictures upon request.