Search results

MD Anderson cancer center tried to use IBM's Watson in a multi million dollar project a few years ago to enhance decisions and treatments for cancer patients. It was a failure because the system used the database humans had been entering info into as its foundation. It was wrought with...

Mine were no problem at all. 1/2" breaker bar (maybe 24" in length) and the appropriate allen head. There is NO reason to use an impact on these. That would be a mistake. Do it with a manual breaker bar. If you dont have one get one. The harder part is figuring out which two plugs to loose...

1 . Wheel spacers 2. Seat belt and ROPS up. 3. If these still make you uncomfortable look at a Ventrac. https://www.ventrac.com/.

You arent going to notice any difference in the BH with 2 gpm flow difference. They are both going to move about he same speed (pretty slow I might add). The MX will be heavier so you are less likely to move the machine when digging. What kind of digging are we talking about? Asking as you...

Wood can do that. My dog loves to leave large sticks (I mean like 6 inch diameter) in the road. Yes he has the "big stick" complex. Before it snows I have to inspect the 1 mile road and make sure there are none I will run over.

As long as you are willing to wait you can find anything! Best of luck and hope you get a low hour, garage/barn kept machine!

25 mph wind and snowing up here today. Its been quite the Winter.

Just go to a hydraulic shop and have them make one. You can order the couplers yourself to save some $$. Flat face are $$$.

Thanks for clarifying. Yes I always use a rag and gloves...gloves and eyewear when dealing with any pressurized hoses. Good reminder for everyone. I just turn my pioneer upside down and tap it on the tractor metal somewhere. I usually just get a little gob of fluid and its good to go.

Easiest thing to do is make an adapter from flat to pioneer coupler. If you disconnect the flat and put the adapter on it right away it wont be an issue. I guess when the fluid cools enough it expands a bit? Or maybe the hoses contract. I have had the same issue on mine, but since making...

John Deere has been making almost all of their own machines since 2017. They will likely still use Yanmar engines, but nothing wrong with that. No it doesnt rule them out.

I think its Social Media. I grew up in a non-digital world, then computers hit in college. Without a doubt the internet and computing changed the world in many ways for the better. However I think in the case of social media it made it worse. Honestly what I struggle with is would the world...

Deleted

Yes but since you are new to the forums we can share with you that you can Private Message any member....and you dont have to share your phone # on the thread!

Now that was lucky! @joesmith123 just be sure delta Safety is a legit person and you are not being scammed. I only mention this because like you they are a New Member and only have 1 post. Could be just fine, just be sure. No offense to delta Safety....just the times.

Correct. YOu would plug that EERO into the LAN port on your PtP antenna That EERO would communicate back to your EERO router or parent mesh device. A PtP antenna if you have good Line of Sight: https://store.ui.com/collections/operator-airmax-devices/products/nanobeam-5ac-gen2 Remember you...

WSM should be here, good place to start. https://www.kubotabooks.com/AutoIndex/index.php?dir=Tractor%20Owners%20Manuals/

The only way a repeater works if if you have it in an area where you have a very strong wifi signal, and can repeat that strong signal out. What you dont want is to add a repeater at the edge of your current wifi coverage area...because then you are just repeating that poorer coverage. If...

It depends on the device. I bought a few off of Amazon awhile back and neither of them worked on a different circuit.

Dont get a grapple that weighs too much try and target around 400ish lbs or your lift capacity suffers.