I spent about 2 hours trying to get the loader back onto my tractor (BX23S) One side always doesn't want to go on correctly and I don't know if the loader arms are the problem or the operator's error.
What did you do to or on your Kubota today?
- Thread starter gurn
- Start date
fried1765
Well-known member
Equipment
Kubota L48 TLB, Ford 1920 FEL, Ford 8N, SCAG Liberty Z, Gravely Pro.
Quick right trurn after TO?
Hell,......It is already melted!
Summer is coming!
No turn required, as the mountain drops away for 1200' vertical before the valley floor, it's much easier and safer than taking off a flat and level runway.
fried1765
Well-known member
Equipment
Kubota L48 TLB, Ford 1920 FEL, Ford 8N, SCAG Liberty Z, Gravely Pro.
"mountain drops away for 1200' vertical"
"much easier and safer than taking off a flat and level runway".
Kinda depends on how close end of runway is to 1200' drop off.
Almost had a very bad day when moving material in the bucket, so I decided to make a mount for some rear suitcase weights.
I used the 3pt arms and took some angle iron and welded wings onto it and drilled some holes so I could bolt it to the arms. The goal was to keep it as tight as possible since I need to get in and out of some pretty tight spaces.
Found some weights that matched my tractor perfectly on marketplace, too. 55lb each, I now have another 275lb on the back.
I used the 3pt arms and took some angle iron and welded wings onto it and drilled some holes so I could bolt it to the arms. The goal was to keep it as tight as possible since I need to get in and out of some pretty tight spaces.
Found some weights that matched my tractor perfectly on marketplace, too. 55lb each, I now have another 275lb on the back.
Almost had a very bad day when moving material in the bucket, so I decided to make a mount for some rear suitcase weights.
I used the 3pt arms and took some angle iron and welded wings onto it and drilled some holes so I could bolt it to the arms. The goal was to keep it as tight as possible since I need to get in and out of some pretty tight spaces.
Found some weights that matched my tractor perfectly on marketplace, too. 55lb each, I now have another 275lb on the back.
Very cool!
That's getting it done.
Looks like the chain attached to the rebar going through the hole in the weights should be going in the downward direction. That would help keep the weights in place, if there was ever an occasion for them to try to lift out.
Looks like the chain attached to the rebar going through the hole in the weights should be going in the downward direction. That would help keep the weights in place, if there was ever an occasion for them to try to lift out.
The 3pt arms drop when the tractor is off and all the weights fell off with quite a bang. It's just holding them up. I'm looking for another way to secure them going down
RCW
Well-known member
Lifetime Member
Equipment
BX2360, FEL, MMM, BX2750D snowblower. 1953 Minneapolis Moline ZAU
Driveway was in decent condition, but needed some high/low spots smoothed out.
Boxblade with a long top link is my go-to. We’re at the bottom of a hill, so controlling sheet flow of water is paramount to avoid washing the driveway out.
Profile of it has proven pretty good, so I try to do just a little bit a time to prevent changing the drainage pattern too much at once.
Boxblade with a long top link is my go-to. We’re at the bottom of a hill, so controlling sheet flow of water is paramount to avoid washing the driveway out.
Profile of it has proven pretty good, so I try to do just a little bit a time to prevent changing the drainage pattern too much at once.
Last edited:
Maybe some stock on both sides welded to your angle that has holes lining up with the weight hole.
Just a thought seeing it assembled so far.
Bill
fried1765
Well-known member
Equipment
Kubota L48 TLB, Ford 1920 FEL, Ford 8N, SCAG Liberty Z, Gravely Pro.
Mounted a little toolbox to the BX using the SMV hardware. Turned out pretty good. Time will tell. Nice to have a place for some channel locks, gloves, rags, grease, etc.
Attachments
JimDeL
Well-known member
Lifetime Member
Equipment
BX2380; R4 tires; 54" MMM; FEL w Pirahna bar; Ballast Box; BXpanded skid plate.
I used a similar (50 Cal) box on mine, but removed the SMV hardware, bolted the box sideways to its bracket, and remounted the SMV hardware to the outside of the box. Mine's gray to match the ROPS.
If my SMV bracket ends up bending, I may have to change plans and do it your way. Your set-up can probably handle more ice and cold beverages.
I used the grapple to remove leaves out of the ditch that runs along the side of our driveway. Then used the land plane to work the drive way up a little.
Took the grapple off to put the buck on and the land plane. I was going to remove the FEL and need the bucket to do that.
Greased the FEL, grapple and tractor. Took the FEL off the tractor to change the oil. Cleaned off the screen that is in front of the radiator and checked the air filter. Also check the hydraulic level while I was at it.
Took the grapple off to put the buck on and the land plane. I was going to remove the FEL and need the bucket to do that.
Greased the FEL, grapple and tractor. Took the FEL off the tractor to change the oil. Cleaned off the screen that is in front of the radiator and checked the air filter. Also check the hydraulic level while I was at it.
Yes and I’ve looked at a few manufacturers, but haven’t found the right one yet.
ken erickson
Well-known member
Equipment
B7100 hst, 2650 front mount snowblower, L2501 hst qa loader
I spent the day at my land yesterday moving storm damaged trees. Early in the week we had an extremely wet heavy snow with some moderate high winds.
I am still dealing with the Scot Pine die off, which is a good thing, and anytime I have a weather event a lot of the dead but standing Scots fall over onto my trails and or prairie plantings.
It was good day to put "smiles" on my tractor. lol.
I am still dealing with the Scot Pine die off, which is a good thing, and anytime I have a weather event a lot of the dead but standing Scots fall over onto my trails and or prairie plantings.
It was good day to put "smiles" on my tractor. lol.
A little coolant drain n fill on the L today. Super easy with the Schwaben vacuum tool!
