Major road work!

random

Well-known member

Equipment
L3301, bucket, backhoe, grader, plow, harrow, cultivator
Nov 2, 2020
717
401
63
NC
Not a project, because I had someone do the work. I've mentioned it before, but my road suddenly got a lot worse during the snow & rain in january:

road1a.jpg


road2a.jpg


road3a.jpg


I was planning on dealing with it this summer, but this couldn't wait. It was also getting hollowed out underneath along that pipe.

A couple weeks and several thousand dollars later, I think I won't have to worry for a while:

road4a.jpg


road5a.jpg
 
  • Like
Reactions: 8 users

Jchonline

Well-known member
Lifetime Member

Equipment
Kubota L6060, KX040-4, M7060, RTV X1100C, M62 (sold)
Oct 28, 2018
1,389
602
113
Red Feather Lakes, CO
Nice work! Riprap around the culvert outlet will help erosion tremendously.
 
  • Like
Reactions: 3 users

NCL4701

Well-known member

Equipment
L4701, T2290, WC68, grapple, BB1572, Farmi W50R, Howes 500, 16kW IMD gen, WG24
Apr 27, 2020
2,788
4,227
113
Central Piedmont, NC
Looks like your new culvert is a wee bit bigger than the old one water was running around (and rightly so). Whoever did it, pretty job.
 
  • Like
  • Haha
Reactions: 3 users

Motion

Well-known member
Lifetime Member

Equipment
Kubota MX5100HST/FEL
Aug 17, 2020
540
302
63
Mandeville Louisiana
Looks good. The RCP appears to be 18 inches, I'd suggest adding two precast headwalls and larger riprap on the downstream side.
 
  • Like
Reactions: 1 users

random

Well-known member

Equipment
L3301, bucket, backhoe, grader, plow, harrow, cultivator
Nov 2, 2020
717
401
63
NC
The original pipe was somewhere around 18". Water was running over the road at least a foot deep when Matthew hit us. Had a couple other storms where similar happened but not quite as bad. The old pipe just didn't have the capacity.

I don't think that's going to be a problem now.

Thanks for the additional tips, I'll check that all out in a few months, when I recover from the hit!
 
  • Like
Reactions: 1 user

North Idaho Wolfman

Moderator
Staff member
Lifetime Member

Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
Jun 9, 2013
30,180
6,347
113
Sandpoint, ID
Did they put any typar (road cloth) under all of that?
 

random

Well-known member

Equipment
L3301, bucket, backhoe, grader, plow, harrow, cultivator
Nov 2, 2020
717
401
63
NC
There isn't any on my road anywhere, so I would guess it's not a major issue.

I don't know what your frost line is (since you mention spring thaw) but I don't think it's relevant in this case: they went all the way down below the current river bed and rebuilt it from there. Not sure where the fabric would have gone.

What you describe isn't an issue I've seen happen anywhere on the road, so I'm guessing it's not an issue.
 

North Idaho Wolfman

Moderator
Staff member
Lifetime Member

Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
Jun 9, 2013
30,180
6,347
113
Sandpoint, ID
Yea you're in NC so not much of a frost / deep freeze issue.
 

Daren Todd

Well-known member
Lifetime Member

Equipment
Massey Ferguson 1825E, Kubota Z121S, Box blade, Rotary Cutter
May 18, 2014
10,146
6,569
113
Vilonia, Arkansas
I'm assuming you upsized the cuvert when replaced?

County minimum where I lived was 18". That being said, we were in a low spot and the ditches handled the runoff from the surrounding area.

So where 18" was perfect in most of the area. Two of us had 36" culverts, the down stream from. Us was 2- 24" culverts on the next drive.

Then the county i their infinite wisdom put in an 18" culvert below that drive way 🥴🥴🥴

Needless to say every gully washer that came threw caused the 18" culvert to back up and our driveways to flood. 🙄🙄🙄

After some serious complaining and then the residents on the street threatening to start billing the county for repairs, they finally came out and replace the 18" culvert....... with a single 24" culvert. 😕😕😕😕

Road still flooded on occasion, but at least it wasn't every single heavy storm.

Someday they might get a clue and match the rest of the street.
 

fried1765

Well-known member

Equipment
Kubota L48 TLB, Ford 1920 FEL, Ford 8N, SCAG Liberty Z, Gravely Pro.
Nov 14, 2019
7,843
5,066
113
Eastham, Ma
Almost certain they did not.
A lot depends on the base material.
I had my 2,200 driveway dug out to 3' deep, and back filled with pit run gravel.
Top was 6" of crushed 1-1/2" minus, plus 3 inches of of 3/4" minus.
Worked out well and lasted for the 13 years I lived there .
Minimum Winter temp was 5 degrees.
I graded it with a meaningful crown twice each year.
 
  • Like
Reactions: 1 user

random

Well-known member

Equipment
L3301, bucket, backhoe, grader, plow, harrow, cultivator
Nov 2, 2020
717
401
63
NC
I'm assuming you upsized the cuvert when replaced?

County minimum where I lived was 18". That being said, we were in a low spot and the ditches handled the runoff from the surrounding area.
Private road, no specific requirements that I know of.

May not be easy to see in the pics - replaced the original 18" with a 48". I think we'll be ok :)
 

Daren Todd

Well-known member
Lifetime Member

Equipment
Massey Ferguson 1825E, Kubota Z121S, Box blade, Rotary Cutter
May 18, 2014
10,146
6,569
113
Vilonia, Arkansas
Private road, no specific requirements that I know of.

May not be easy to see in the pics - replaced the original 18" with a 48". I think we'll be ok :)
Yeah, couldn't tell size from a picture on the cell phone. Yup!!! You should be good 👍👍👍👍👍👍👍