Search results

I thought the front axels took 90wt gear oil after looking at my book. That is what I put in mine B7100. Also, my book said to fill the oil to the top of the axel housing? Only found two plugs, a drain and one on top of the axel housing on right side. That seemed strange to me, as...

I recently had to split my B7100 for clutch repair. When I re assembled I assumed I could get driveshaft back together after reassembly, but I could not do it. I even disconnected it at the Hydro gearbox (spring roll pin, hard to access), with no luck. I ended up having to cut off a small...

We use a Kubota 5' Mid mount mower, We are running on high side PTO speed which is the only speed the front PTO runs on. I would have thought running a higher RPM would probably be a little better at cooling the Hydro unit since that fluid is being pumped. On engine it is convection flow...

My lovely wife runs the B7100 to mow the grass. She has a habit of running the engine a lower RPM than I would to cut the grass, sometimes dogging the engine a little. It cuts amazingly good even at lower RPM if grass is not thick. I have always run my diesel tractors just below the PTO...

Do you have factory seat, mount bracker and suspension springs?

a poor ground can cause slow crank speed or a worn starter can also drag and cause slow cranking speed If battery is good, wires and connections are good, I would look at starter.

My B7100 front differential @ driveshaft boot/housing had gear oil in it when I removed rubber boot. Probably my seal is leaking some. I actually put some gear oil back in there when I re installed thinking it would help lubricate the U joint and splines and oil would seek its own level...

Was wondering if anyone had installed a torque generator style poser assist on a small kubota such as those offered by char-lynn. They basically go in the steering column between the steering wheel and the steering gear box. maybe it would be too long? Seems it would be an easy add on if...

I probably did my measurement wrong, but I think I measured the height of fingers (new Kubota pressure plate) before installation and checked they were all within the tolerance of each other. After bolting up, checked for the same relationship to each finger beaing nearly identical in hieght...

hopefully picture posted this time?

Got this tractor for $4000 delivered. 1000 hrs. It had just gotten a new clutch installed supposedly. I Had to put new clutch in almost immediately ($500 bucks after I did the work) cause previous owner bagged out when he did the repair and skipped the pilot busing. tres are good, deck is...

I would have that flywheel resurfaced.

adjustment is pretty straight forward. I could look it up in my book if you can't find it.

I had to re tap some holes on a duetz tractor into the cast steel of the rear end. It taps easily. you'll need to step up in bolt thread diameter size .That is best hope to shoot for in that spot. It might require you pull engine. A machine shop could do it for sure.

make sure you deal with the pilot bushing. I just purchased my B7100 last fall from guy who replaced clutch pressure plate T/O bearing. He did not replace pilot bushing. Clutch failed after about 10 hours of use. due to wobble of input shaft, clutch plate flew apart. I actually had to...

thanks guys, Mine sure does not appear to have it, but thankfully starts easy!

On front axes, if I recall, you fill up with gear lube at the bolt on the top of axel on passenger side (R). You basically fill it up full as I understand it. The rear end is lubricated by hydrostat fluid. My book called for 3.6 gallons capacity in rear end, but mine did not hold that...

try to avoid snapping it off, that wouldmake getting the TO bearing sleeve difficult to get out. Try a small vice grip and pull down as you turn

Assume the knob is on the dash. Do all B 7100's have this? I don't recall seeing one on mine, but I will have to go back and look again.

I hear mention of the decompression lever on B-7100. Is this lever activated by pulling throttle lever towards rear to kill the engine? SHould it be used when starting to spin engine to build oil pressure prior to starting? We have an old Cat highlift that starts that way. When should...