Search results

In Oregon near Astoria, B7200 that has less than 700 original hrs on the meter FEL, newer hoses throughout, replaced water pump, factory service manuals, 4wd, $5K

I was thinking about ways to use my old b7200 to drive a generator & wonder about the faster pto speed and what it would/could be good for, does anyone have any suggestions? thanks..

OK, 1st off the forum & orange tt has been very helpful with the big decision...I'm old but not rich & tractor buying is some serious $... after the dealer quote came through I went online and built the same thing...the basic tractor without all the implements & grapple...turns out the dealers...

About to jump into an L2501...i know i can trust a standard trans for many years...clutch is not covered by factory warranty....HST is not new tech....will it last? advantages? disadvantages? thanks

Hello, my B7200 has an issue, when the key is turned to heat the glow plugs the lights come on the dash indicating power but the glow plug coil on the dash doesn't get red or hot...it was working OK last week...what would you check 1st...2nd..maybe 3rd as well. thanks!

First part of story: last time i tried to start my tractor, when i turned the key to heat up the glow plugs the gauges all came to life but the glow plug indicator didn't show any sign of glowing and the other dash/gauge lights didn't dim as they normally would if all the current were going to...

Looks like the tractor sprung a leak. I had noticed it was badly corroded around the valve stem when i attempted to check the tire pressure liquid came out. it's an old B7200 and i have had it a couple years and i sure appreciate her abilities. anyway when i noticed a little puddle around the...

I have been getting some good seat time on my B7200, it is my first tractor, i have been working new ground for a veggie garden plot, the top layer of grass and turf is thick and rough, i mowed it and then ran a middle buster all over the plot, then the tiller back and forth, it's gonna need...

I have some fresh ground that i want to make into a veggie garden this spring, i have a B7200 with a FEL and a tiller, a potato plow. i was thinking a boxblade or maybe an open blade for scraping the top turf off, any advice about the right tool for the job? thanks!

hey all, got a 4' john deer brush hog style mower, well used to the point of needing some work on the gear box, i flipped it up and got the cotter pin and castle nut off the spindle end but can't seem to get the saucer/blade assembly loose, it looks like it hasn't been removed since new. i did...

Hey All, i was replacing cooling system stuff, rad hoses, water pump, fan belt. it was going great until i buttoned it up, reinstaled the side panels and messed up the lower hose to radiator....it started leaking all over the place....so i caught the anti freeze and pulled the rad back...

Looking at a ganon 4 way box blade, iv'e been wanting something that can remove turf, grade the gravel drive way, scrape away at the new garden spot before hitting it with the tiller, it has a lever to control the blade i think but the pic's are bad and i thought i'd ask you'se guys. what do you...

He guys, i was replacing the radiator hoses and happen to notice a little greasy seepage under the water pump, it isn't losing any noticeable fluid more of a petrol smell, im in there with the radiator pulled hoses off so i just had to ask :D

I am working with a b7200 and went to do a test instal of the full size PHD and the ROP bar prevents the main beam from fully reaching the mounting point, it seems like it's removable, i'm guessing pretty heavy, but doable, and i figure safer than trying to change other things, if i'm careful...

hwy i don't have much experience with tractors and implements but am wondering? if i put a class 1 with a 28" width mount at the 3point on my little b7200 will i regret it? i have a post hole digger but it looks to be a bit big for the spread of the mounting arms on the tractor, i think i can...

Hi folks, i was doing some work on my little b7200 and wanted to change the oil in the steering gear box, the manual states remove the plug but the plug is at the top of the steering box and removing it seems more like a filling it back up location, i just snaked some thin tubing down in there...

i blew a FEL control hose and went ahead and pulled em all and had some fresh ones made up, after putting them back together the loader goes up and down but the bucket went down when the control knob was operated either way, i need a little help..the tractor is a b7200 the FEL a 1630, the...