Search results

I just got my operators platform back from the local Rhino Liner dealer. $103 out the door. $50 for the product, $50 for labor masking a few areas off, and $3 sales tax on the product. It looks awesome and is very professional looking, and definitely non-skid. I'm not into ghetto solutions...

Is there any reason why a feller couldn't drill a 1/16" hole in the plug or install a gear case breather plug so that the clutch housing drains itself? Something so the leaf cutter bees and mud daubers can't infest.

I picked up my operators platform from the local Rhino Liner dealer and reinstalled it on the M5660SUHD and boy, is it nice! Very non-skid...should be nice and safe with snowy boots on this winter.

Yeah, I've seen stickers like that and have yet to figure out how to use it. Perhaps a designated spot to throw down a magnetic torpedo level or what?? My tractor has a rod that is attached to a pivot point on the bucket curl linkage and it goes up the loader arm with a bent rod through a...

Interesting information...I didn't test drive the larger Grand L series because they were outside my budget constraints nor did I test drive the MX hydros because they were not suitable to me for other reasons. It's nice to hear comments like yours as I take it as a confirmation that I chose a...

I drove a Kubota 3301 hydro and I needed hearing protection from the whining hydrostat even when in low range and very light load on the tractor. The same is true of my FIL's JD 3038e. So one reason is the noise. Another reason is the potential for heat buildup during hours and hours of heavy...

I removed the operators platform from my M5660 to take down to the local Rhino Liner dealer to have it sprayed. Wasn't too bad of a job. The Rhino dealer wanted $350 to spray it in place because they would have to do a lot of masking off areas of the tractor. I opted to put in some sweat...

Here goes...

Ughhh...I'll try! Might have to do some research of the stickies and what not to figure it out.

Took delivery of my new M5660 the afternoon of 11/6/2020. Put 2.1 hours on it over the weekend. I'm pretty happy with my purchase and it will be used to do the chores that the old Farmall C had been doing and a few new jobs that the C couldn't do. I'm liking the hydraulic shuttle! I bought...

The last time I checked, Mahindra rotary cutters were made in the USA by Kodiak and appeared to be very robust construction. Once upon a time, I was going to buy a Mahindra 3550 power shuttle but they got pulled from my local New Holland dealer about 2 years ago. I took that as divine...

Not unusual at all. I bought my Farm Hand by Lee Agra quick hitch three years ago and I'm glad I did because they have been discontinued. Still haven't got my tractor yet but I've never been closer.

Big hands, big feet, big Pete!

Ever since I traveled "out West" and saw my first cattle guards I was fascinated with them for some strange reason and I find this thread intensely interesting. As a boy, I found the western states to be a strange and wonderful place with windmills, cattle guards, oil pump jacks, cactus and...

Glad you weren't hurt but that is cool as heck! Seriously, I'd hang that on my shop wall in a heartbeat!

I watched that video last night and had the same question. The JD interface does not allow you to "change" anything to speak of but has a lot of "read only" information such as PCM codes or errors, all kinds of engine data such as % load, soot load, PTO run hrs, engine load during PTO run and...

Got this from my dealer: Floor mat 3C001-55062 Floor mat fasteners 7 req’d Z67955-51340 Says it fits on the M5660. I plan on removing the floor pan and taking it down the road to the Rhino Lining place and have them spray it.

I just bought 3 of those but the lettering and graphics were fuzzy...like a photo that had been blown up too much. I was disappointed.

I like the Precision Mfg 333D72 clamshell grapple. Dual lid, weighs about 600 lbs, opens 50".

Haven't done it personally but don't see any compelling reason why you couldn't or shouldn't.