Search results

ha ha ha~ It hurts alright~!!!:D Once I've been hit by one of my student, it was hurting soooooo bad. Especially got hit on my nuts and it was winter time~:eek: I'm not sure about impurities but it should be pure CO2, I think. Those CO2 canisters you buy your own and refill it at almost...

ha ha ha~:D:D:D

One of youtube video guy said we could use Paint ball's CO2 canister for MIG welding. Is it true? I'm studying MIG welding a lot right now. but this Paint balling CO2 canister makes me quite interested. 'cause, I have 3 of 20 oz tank with full of CO2 right now. :D Is there any one using...

Thanks for the good site sharing. They have everything~:D I might spend whole day to looking through~ Thank you Eric. Joe.

Hey, Dusty. You've done it again, Huh?! You are sooooooo creative~! My snow blade's Wing cylinder arm's eyelet was keep on braking. so I weld it back on 3 times and I took it to welding guy and he told me my welder is too weak. it is not penetrating deep enough... :eek: So He ground'em all...

Hey~ Scotty, beam me up some side ribs~ PLEASE~~~!!!:D:D:D It is finger freezing goooooooooooood~!:D We had -39 Celsius a few years ago...:cool: A few more weeks, winter will be over and we have to start complain about the Grass and Weeds~:cool: Thank you for the yummy picture~!:D Joe.

I had Zetor 70 hp tractor last year and we had -25 Celsius one time. I had to heat up the heater for 2 hours (1500 Watts) and barely started it along with Ether. :o and I drove down to the parking lot and engine died on me right on highway and it starts and dies again... and I look into glass...

That might been a problem too...:cool: While you starting the tractor and if that wire got damaged on the frame some where... it will blow the fuse....:eek: Have you check the fuse for the ignition switch? Or you could do voltage test on that damaged spot while turning key to starting...

Tractor's own battery to start~ That is good news.:D Solenoid should have 3 terminals total. 2 terminals are heavy gage wire, and 1 terminal is smaller gage wire. On 2 heavy gage terminal, One side should get 12 volts all times. and the other side should get 12 volts too when starting the...

As Traildust said, it is cookie setting matter. "Remember me" and "cookie setting" will solve your problem.:D and update the "windows update" too. I have one wish too...:D A lot of member's pictures are too small including profile images... so can't even see what it is. Sometimes I wish I...

Have you jump the wire from tractor's own battery? or was it from the other battery? If it was from tractor's own battery, start to check every each safety switch. Do the contunuity test on each safety switchs. Anything fails, that is the problem for you... and let me know which safety...

First of all, do the continuity test on the Negative ground wire. put one of lead to the post of battery on Negative. and the other lead to near around grounded negative wire. If it has no resistance it is good. if it does, your problem is right there. After that test, put Negative lead...

Wow, Is it your tractor? or Space shuttle~~~??? Awesome job~! Joe.

Have you adjust your clutch pedal adjustment lately? If you haven't, it is the time to do so... Good luck. Joe.

It sounds like safety switchs matter. Clutch depressed, PTO dis-engaged, gear shift is in neutral, Sit on the seat and so on... If you did all that starting procedure correct and still not turning starter motor... it could be your starter motor's solenoid trouble. Check voltage of starter...

Well, I don't know anything about B2920. but my B7510DT has ignition switch to "OFF" position to kill the engine. It has engine shut off solenoid built in. So in my case, I could connect kill switch to ignition switch and I could shut off the engine that way. I hope you have that too. Any...

Thank you. I wish I had a bit heavier gage on the sheet metal wings...:o My favorite welding guy didn't have it in stock at that time. So, I'm going to take it to him some day add some support beam to increase streangth later time.;) And that control arms and so on, idea came from Radio...

Thank you Dusty and Greg...! After I modified Wings again, I need to test it out but now no more snow~~:D:D:D

6' Snow blade earned 2 wings now and I do really love it. I was working on this Wings for a while but had a few incidents...:o A couple days ago, I finished all the mechanical work done on this wings. but electrical work hasn't done. 'cause, I couldn't find right wires for it. and I had to...

Yeah, you could tell that cab is HOME MADE, Huh~?!:D I made that first time in my life time with MIG welder~! Never weld it before either.:( and it turned out not too bad, but still I have to fix a few more stuff in this summer. I was working with my welding guy in town here for 5 hours...