Search results

Well done, excellent, best solution yet for this very difficult problem seen yet. Others would be well advised to save this posting if they do not have under carriage protection. Thanks for posting this very "easy" solution.

The design works great as the square tube is very strong and keeps the round thick wall tube straight, where there maybe some flex is when the forks are slid into the center position and then there is no wear blade on your front edge of the bucket. My wear blade is very strong from WR Long...

me too. seems just too much space, for a tractor that simply doesn't have a 1/4" to spare. However, did find a rather interesting spot for a horn and will post whenever get the wiring done.

Yes, I use them when need too about once a month so far, but then been doing a lot of digging, loading and backfilling. However, this summer they will get a lot more use with the projects planned.....by you know who. And, yes have spring pins on the end and they are on/off in a jiffy. The...

From an earlier tread, for the new owners. Here are two of the easiest mod to do on a small tractor. First every morning when I go out to the rig-a-dig the BH stabilizers have settle a bit and this is normal on hydraulics, but unsettling if you forget and barely clear the door frame. So took...

ok here are the pictures

copied this from an old tread, hope the pictures come through. Hi Folks, here are five in progress pictures of the new forks for the FEL. First pictures shows dealer installed W.R. Long Inc. wear bar (good investment, saw a bucket without one and looked like 50 years of use in only 5 years)...

Welcome to the BX world. Had mine for a couple of years now, and yes the fuel gauge will take a little getting use to, I’m in and out of excavations so notice that the gauge will fluctuate noticeably as you move up and down grades, however sitting level for a minute will show the true reading...

Both the stabilizers and the quick hitch work great together, strong, easy to use and stable on the BX25D.:)

Welcome to the world of the BX25D TLB. Some dimensions: front to back FEL blade to rear of folded BH 15 feet top of BH off deck 5' 8" top of ROPS off deck 7' 2" but really need at least 7' 8" to be sure. out to out stabilizers and pads down 6' 10" and fully up 4' 4" weights FEL 496# Tractor...

this same top hook problem occurs in a number of older type of units (pre QH times) and I will have a welder cut out the center of angle brace, lower it by bending it down to a new cross bar welded to the two side braces. This allows the top hook to rise up and connect without have to remove the...

Road Test speed control pedal Using a level section of the paved road, stretched a long tape down on the shoulder and starting 50’ from the “0” mark (where I took my foot off the pedal) did six runs for each of these tests (over 48 runs in total). 3200 rpms 4 wheel drive Low gear (turtle)...

for those interested Paul says he will post a new video in a couple weeks on a complete service of this problem. Stay tune as they say, this may shed some more light on this issue.

Hi folks, Paul posted and interesting video on HST stopping issues and Coyote Rod posted a video on this same problem and possible solution. Are there any comments, concerns, solutions or discussions on this important issue?:confused: Thanks for any input you may provide. and mine does not...

A trip to a large Kubota dealer showed nearly ever larger model than the BX had OEM installed ridge stabilizers or were an installed option. :confused: Secondly, not every implement takes the QH. The turn buckles provided for the BX by Kubota are a bit cumbersome or to say the least fiddly and...

Like a lot of good OTT members have seen and use, they are crafted by Mark Hodge.

Three, I have three along the top edge of the FEL bucket. One near each end and one dead center. This arrangement works extremely well for a variety of uses and allows lots of flexibility when lifting or moving things, also the center one makes a great sight line for lining up the tractor...

It took longer to sign the postal slip, unwrap them, then it did to remove OEM turn buckles and install the new stabilizers. They work great.

Welcome to OTT great site, lots of folks have posted many a good things to do to your new rig, some things you should do, and some things that my not be a good ideal. Check the treads and postings for all kinds of good information sometime ideas and ways of doing stuff comes along that just may...

hang a short chain inside the bucket or put some small holes in the back of the bucket to let then air in. may not work for all soils.