Recent content by HorsPower

Kubota L4479 front mount snowblower with L4455A subframe / front hitch assembly. All brackets are included to install on a Kubota L40 or L60 series tractor. This unit will fit L3560 , L4060 , L4760, L5060 , L5460, L6060, L3240, L3540, L3940, L4240, L4740, L5040, L5240, and L5740. The unit will...

If your AGM lasted 7 years, I think you are throwing money away by trying to squeeze in a group 31? What problem exactly are you trying solve? Does the tractor start after you have blown snow all night with all of the heat and lights on? If not, it sounds like an alternator upgrade would be...

14 gal fuel caddy. I have a small electric hoist in my shop so I opted for the gravity feed version. I hoist it out of my truck and up into the air to fill my tractor. https://www.amazon.com/dp/B0DQPW377J?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1

I found a lightly used B-50 agrimetal blower on Facebook marketplace. It is absolutely awesome for blowing leaves off of my large yard (and blowing sticks / limbs / debris off of my driveway). I have even used it to clear light / fluffy snow. I need to do this same modification to my blower...

You do not have to cut R4's deep to realize a SUBSTANTIAL improvement. I grooved mine about 1/8" depth. I have a L5740 with filled rear tires, max rear wheel weights, plow / or blower on the front and typically a heavy implement on the back when moving snow. I had questioned grooving / siping...

R4's are the worst on hard pack snow / ice! I have a L5740 with filled rear tires, max rear wheel weights, plow / or blower on the front and typically a heavy implement on the back when moving snow. I had questioned grooving / siping the tires for awhile and had ordered the tire groover off...

Understood, that is unfortunate. That said, unless the driveway is chunking / breaking up and you are concerned about running chunks of asphalt through your blower, it still sounds like you would be better off removing the shoes completely. Your replaceable cutting edge will take the wear and...

Why would it ride on either side? Does you drive have excessive crown? I have a L4479 and am not using the shoes. It rides evenly on the cutting edge, and does not ride on the ends. I would not want to use the shoes on a paved driveway as it wouldn't scrape clean.

Wanted to share my new snow setup on my L5740. Totally overkill for most snow weather events here in Maryland, but it's "nice to know you can." Luckily we just had a couple decent snow events so I was able to test everything out shortly after building it. Previous setup: I had an older 8'...

Dave, are you clearing a paved or non paved driveway? Assuming non paved, I'm surprised to hear your shoes are wearing that quickly. If you are on a paved drive, I would remove the shoes as the cutting edge will distribute the weight better.

I realize this is an old thread, but in case anyone else comes across it, L5740 grand cab models come with the gear already install in the case, adding the mid PTO is as simple as removing the case cover under the machine and installing the mid PTO. I just installed a mid PTO on my Grand L5740...

What is your typical annual snowfall amount? Loader mounted blade with a rear three point snowblower (like Mcmxl has) is a pretty tough combination to beat. You only need to mount the snowblower when snowfall is adequate to merit doing so, and the snowplow is easily removed from the loader...

I decided to just cut the brush guard and weld it to the front subframe mount so that I don’t have to switch back and forth.

Over the weekend I also built an underslung mount for my Meyer. Haven’t used it yet, but looking forward to not having the plow hang so far forward off of the loader like before.

I realize this is an old thread, but I thought this might be helpful to others. For the past few years I've had a 8' Meyer plow on a SSQA mount for my L5740 loader. In small storms it is nice to have the extra width, but it is a lot of plow hanging off the front of the tractor. With deeper...