Fixing hole in side of block

[D2Cat]

I need to replace a bushing for my Kubota front end quick connect, Kubota wants $50. Do you think I can use a stack of washers?
1-1/8" OD x 5/8" ID x 15/16" long.

Do your really think a bushing is necessary? Put a piece of hose over the bolt and install.

 

[joesmith123]

put big bolt on loader to tractor, put together all the hydraulic that control loader

loader almost attach to tractor, get big bolt and washer on all 8 connecting bolts on 4 side of tractor

start to figure out the hydraulic, some connectors are rusted out, weld on new ones

basically: clear the area, bring all hoses/fittings and get it figured out

yes, finally back at the shop, declare more task so it is on the record:

dont forget to adjust the idle (should have done it before putting on loader)

also, I can install some of the other parts that are orange: dash pieces, exhaust hanger, put the hood on, try to run it without access to decompression knob, etc

summary: put all bolts connecting loader to tractor with big washers on both side, fasten tight

clear out entire area, bring a pallet and bring all hydraulic hoses and fittings to it,

make progress on these task in the beautiful perfect shade, grateful to be at this point

@Henro

you are not admiring my approach, you are joesmith deep down, just take the filter off and let her eat

This thread is a mirror showing you nature/yourself...

remove all cinderblock and lumber away from area, clear your workspace

(i write this to talk to you or myself if I read this later)

Here's a pile of lumber/cinderblock that was used to put the loader on, and the infinite amount of cheap jack to line up bolts, and the DEEP crawling on ground trying to get the bolts in

I was thinking: why does this make me so dizzy and consume all my power?

That task where you bend down get real deep underneath, then have to lift your entire existence over a little washer,

is a huge energy consumer. I am at the point where I want to rig up massive structure above machines, then I simple lift up entire machine and make those areas accessible and not make me dizzy

you cannot "work hard" because you'll be so tired and unable to make progress, and not get the gold...

bring the blocks back out because you cant reach anything underneath without getting a head injury

spend another hour chest to the ground getting blocks in place

yes, deep in this region, cutting your arms tightening the bolts, trying to emulate how it was,

dont make it too perfect, rig it back up good enough,

got the bolts fully fastened on rear of tractor to loader connection, rig up the side piece that hold the exhaust hanger, clamp around exhaust

now: do the other side cover, get the biggest bolts laying around and put them on front bracket of tractor to loader connection,

might take off steering wheel, and put the dash over the diesel tank, move my glowplug/start switches, etc

keep reassembling, dont make yourself too dizzy, comprehend the task and how big it is/was,

"dont be in big hurry to get going sincce you already put 5-6 month of labor, whats the hurry all of a sudden?"

some methods being using to line the bolt holes: crow bar and lumber, cheap jack pushing up on loader,

got both side pieces that connect to fender and tractor attach, got the exhaust hanging fastened, put all 8 bolts fully fasten that hold loader to tractor, and the 6 bolts that hold tractor to loader front side

take off steering wheel, put the diesel tank cover, figure out your switches, bring all the hydraulic fittings and hoses to the tractor

narrate more once you get to that point

slow your roll, go smoke some meat, try to enjoy the reassembly...

while fatty meat smoke, you fasten the hardware, take out steering wheel, take out your switches, install dash, put few bols to mock everything, put the hood on, put steering wheel back on

"woah there she is, coming back to life, going back in time..."

Take hood back off, clear out a pallet, bring all the hydraulic part, bring the hydraulic controller, mount it...

she's mean, angry, ready to tear the earth, you can sense it

clear out a pallet, bring all jic 8 fitting/hose/ and the controller

mount the controller, start to mock the hose connection...

controller: take it apart, clean with compress air and diesel, mock it up onto tractor, drill one hole to fit another bolt

last I mocked this up, it fell and tractor ran it over, now the levers are not turning

plan: get the bolts on it tight, put real pressure on the switch trying to see if it can work again

 

[Henro]

put big bolt on loader to tractor, put together all the hydraulic that control loader

View attachment 142451

loader almost attach to tractor, get big bolt and washer on all 8 connecting bolts on 4 side of tractor

start to figure out the hydraulic, some connectors are rusted out, weld on new ones

basically: clear the area, bring all hoses/fittings and get it figured out

Joe, I have to say I kind of admire your approach.

Personally, I have to understand what I am doing before I do it! Seems like you approach things differently, but things work out in the end...

 

[rudder35]

yes, reinstall orange parts, get L295 attach to its freshly painted loader, and other many tiny task

View attachment 142327

ton of task going through your mind: fix the seat, put on the fenders, take off steering wheel, reinstall the dash and components, cant put the hood on because I need access to the decompression lever, somehow fix that later on so you can put the hood on,

simplify plan and be practical:

fix the seat, put on the fenders, put on all wheels and get it off block, raise the loader, get L295 attach to the loader,

then at that point you can do ton of task including:

hydraulics for loader, put the hood and maybe salvage the decompression mechanism, maybe move my switches from the diesel tank to the dash, put the exhaust hanger,

View attachment 142328

grind down sharp plastic, focus on the bolts and alignment,

View attachment 142331


grind down seat, hit with compress air, got 2 or 3 bolt on the seat more straight, good enough for now, put towel over it, keep show moving

View attachment 142333

install fenders, seat no longer sharp, all it needed was 5 minute grinding wheel

put on all 4 wheel, get L295 off of block, lift up on loader, ease L295 into position to get bolted to its loader...


View attachment 142348

get the wheel on, lift up on tractor, take out all blocks, she back on her feet

dont scratch paint too much when putting wheel back on

assess the charging/hillbilly ignitiioin situation, get her started, go get her connected to the loader

i wish bx1500 was not fully seized, I would lift up and down on loader using its 3 point hitch,

as I get L295 chassis bolts to line up with the massive freshly painted loader

View attachment 142359

small win: the hillbilly ignition work. It killed the battery, recharged it, and started without a jump, and

seat actually comfortable in the state it is in

move L295, line it up with rails on loader

View attachment 142358

rails have to be lifted where I point to clear chassis,

lift up on the rails using cheap jack, get over the hump, move L295 forward, drop loader rails, align all bolt hole, get bolts in there

View attachment 142360

keep lifting up on loader until axle goes past the brackets, then drop the loader, move L295 forward, line up front bolt holes, then rest of bolt hole

View attachment 142363

wrestle around in the dirt getting blocks in place, get up maneuver L295 slowly forward, get back in the dirt, lift up on certrain areas, almost got bolts lined up

View attachment 142377

somehow got 2 bolt in one corner, lift up on bucket with cheap jack, get your dolly underneath, now

use dolly to pull left/right, use cheap jack to lift up/down, get your bolts in, make sure you put washer, fasten them tight

Finally got the six bolt that hold front of loader, and got a mock bolt into the four corners holding onto tractor

this task take way more out of me than all the engine/piston/gear work,

underneath machine, covered in dirt, one wrong move and you injure yourself especially head,

in the dirt, dragging blocks all over, going deep underneath to fasten a bolt, dont forget a single detail or you wear yourself out from too much motion

unable to move single muscle, covered in dirt and kubota orange, narrative ask:

"now you see how deep you were in that engine and how much work it take to get to it?"

Joe,
If you stop by a carpet store their dumpster will usually have carpet you can get for free to cover the dirt.

 

[hagrid]

This universe doesn't have that much carpet.

 

[Workerbee]

Maybe he could finish up with pergo

 

[joesmith123]

Figure out hydraulics

drill out new hole for bolt to hold controller, fit 2 strong bolt hold controller well

take off boot that cover controller solenoid, hit solenoids with hammer, successfully able to move lever now

now: study the lines and guess where they go trying to use hillbilly logic, connect controller to the hardlines, assess the whole situation

Plumbing hydraulics, plan it out

Ok yes I understand: 4 lines going to 4 hydraulics that have in/out ports, total 8 lines to control everything

 

[WI_Hedgehog]

Do your really think a bushing is necessary? Put a piece of hose over the bolt and install.

I'm just going to use a carrot, it's already orange.

At least I didn't run over my hydraulic valve body...cringey. But I also didn't smoke a fatty, so I didn't leave it lying lost in the dirt.

Speaking of smoking a fatty, anyone notice:

 

[D2Cat]

Joe, when you get your paint on the hyd fitting internal threads and flared seat you could have a problem getting it buttoned up!

 

[joesmith123]

Hydraulic continued

use hillbilly logic to imagine where the lines go, left/right of controller go to bucket, up/down on controller go the arms of loader

the controller: where i point is what I think is the input / output from transmission to controller

beside the 8 line that control your hydraulic arms, there are another 2 lines:

1. transmission to controller
2. controller to transmission

When taking apart the other L295 tractor, I remember noticing a line out of the transmission

I assume this line go the the controller input

But, what about the controller output? How does that get back to transmission?

go make progress on the lines that you know need to be mocked, while you let question marinate of the unknown line

basically, consume all the plumbing that you already have while figuring out the rest of the hydraulic

tasks available: get your 8 lines connected, mocked, installed, weld on new fittings where it rusted, do metal work etc

if that task done, get nice fabric lying around, cut and cover onto seat, self tap in screw and big washer on to back to hold it tight

take off steering wheel, give it nice smooth jb weld job and fresh black paint to smooth out the cracks of 45 year old steering wheel

make hardline hydraulics: yes, I remember dinosaur teaching me to make hard hydraulic line, and I do have flaring tool, and male/female connectors, and extra hydraulic hoses to do:

if you cant run rubber hydraulic line from transmission to controller, make a hardline and then use a small rubber hydraulic line, start to imagine that task

Everything is jic 8 and can easily fit together

escalate your hydraulic effort: bring cheap table close to tractor, bring all hydraulic related part

decide to come straight up out of the controller, and bend into the 4 port

2 bigger hoses can be half foot shorter, having trouble consuming the smaller hoses intended for this area,

proceed: save those long hoses for the long shots, try to use 90s etc to make use out of the tiny hoses,

dont think about it too much, consume the parts that you have then later assess what you need

4 lines coming from controller, label them depending on the action of controller

in my case: 1 is right, 2 is left, 3/4 is up/down

dont worry if they are off, later once you get the hydraulic flowing, you can switch them at the controller, but

make sure the numbers match where they split, ie connect them in the way they are numbered in picture

adapter I have does not fit these factory fitting, check to see if others are like this, and figure out the conversion

count number of fitting needed for this conversion:

8 total fitting, 2 are rusted out

convert:
6 converson: (size could be 3/8 Im guessing) - jic 8 male or female

2 rusted out: get the proper drill bit that can fit the fitting you have tight, then weld it shut

take picture of exact fitting used for the rusted out ports

jic 8 fitting next to rusted out fittingg that was sliced

plan: get exact drill bit size of jic 8, drill out the hole bigger, get your fittin in tight, weld it on, or

try to figure out that method where you make thread, drill the hole out a bit bigger, then get that thread maker that would match the thread of my fittings (jic 8)

up close picture of fitting, ruler say 3/4 inch encompass even the thread

summarize so far what you need:

6 plumbing conversions to go from factory to our thread

drill bit that fit our thread to drill out those two cut ports

hoses: mock up what you have, then come back and articulate exact hose needs

 

[WI_Hedgehog]

Joe, when you get your paint on the hyd fitting internal threads and flared seat you could have a problem getting it buttoned up!

Not to worry, the grit in the hydraulic system will eventually plug any leaks.
(plus lower the hydraulic pressure enough so leaks are less of an issue)

 

[joesmith123]

More hydraulic

yes, mocked up all the hoses going to their final destination

let me know if 1 and 2 are OK being that short, I can also add 90s that would make the route easier on the eye,

My guess: probably get a few more 2 foot hoses just to cover if some are too short,

I can see 3 and 4 needing to be longer, since it extend forward, needing more slack

so far we need:

6 adapter that go from the factory smaller thread to our thread

really good quality drill bit exact size of fitting we want to put into the rusted out ports

quantity 2, two foot lines for connection 3

quantity 2, four foot lines for connection 4

at that point we should have enough long/short/medium hoses in case it is not correct

let it all marinate while you do other task since the two lines going from controller to transmission and back are not yet understood

find the port that come out of transmission, make sure you have that thread, then imagine the line going to the controller

find the return port from controller to transmission: imagine the route it take from controller to that location

you might need more hydraulic line for those connections

few task to do while you wait for nature to reveal answer:

make your adjustment on the idle: get her running, make half turns out on the idle until she start to see saw, then go in a quarter turn

take off steering wheel, make good batch jb weld, use small spatula to fill in the gaps, let it cure a bit, grind down the areas smooth

the seat: it is not bad in the state it is in, but sore on the eye

mayybe get black towel, cut it and fasten it to back of the seat

mightve found port that go to controller

this picture is the other L295 that this loader come off of

underneath your left foot is this port coming out of transmission,

I'm guessing take this one off and put it on the current L295, and make sure you can adapt to that thread

underneath left foot of current L295: bolt where that other tractor has that hydraulic line

Rear of L295 that had attachments: this is connected to the rear spindle

do I need this for the loader or is this just for the backhoe attachment?

clean front grill, reinstall onto hood

reinstall front grill headlight assembly, cant figure out how the hood sit on that bracket left in the picture

I remember having a rod that would go through the brackets that were welded, but

I cant connect the brackets properly, let it marinate

take off steering wheel, mix jb weld, get gloves, fix steering wheel

jb weld steering wheel, flip steering wheel, fill the low spots/cracks

let it cure, go adjust the idle, test out your hillbilly ignition, maybe find new mounting point for switches

turn idle adjustment half turn out, hillbilly ignition working fine, she start right up and charge battery,

hissing sound gone: she busted open her exhaust manifold, need a good weld since jb weld cannot handle the heat

she is idling fine, no see saw, and not shutting off on her own

L2773 loader: found this on kubotapad, and it even tell the size of the hoses, and they are 3/8

use this information to see the size hoses they use, and emulate those, and try to get the adapter to go from: 3/8 female - jic 8

jic 8 will screw into regular household 1/2'', today I think I confirmed that

yes, summarize the size hoses they use:

controller to hardlines, 4 hoses: 30 inches, hose 13 in the diagram

long hoses are 38 inches, quantity 2, hose 8 in the diagram

hose 10: front hoses that control bucket, all of them 19 inch length, quantity 4

hose 14: connect to short side of arm hydraulic, they are 10 inches, quantity 2

that should be it:

4 hose 30 inch
2 hose 38 inch
4 hose 19 inch
2 hose 10 inch

total: 12 hoses (8 plus 4)

 

[joesmith123]

How do the hydraulic lines run from controller to tractor and back?

hydraulic system:

I have no clue how the controller connect to the tractor

I read in WSM that one of these lines is pressure, and other is return

maybe 50 is pressure, and 10 is return?

Someone please shoot from the hip and tell me where to put the lines

A picture would help, or you can use the image and circle where you want me to run the line from the tractor to the controller

L295DT Hydraulic Issue

Im hoping someone out there can help me I have a 1979 L295 DT manual trans with only one hydraulic pump mounted to the rear of the fuel pump and a model 1200 loader with 2200 hrs that I only use occasionally Was using it the other day and loader and bucket functioned properly and shut it off...

www.orangetractortalks.com

I try to read this thread to decipher the answer, but there are no pictures or diagrams

ok here is simple plain diagram, study this diagram 6 or 7 time until you comprehend

Ok, the suction line is input into the controller, and the return line is output on the controller

suction line for this tractor would be:

that hydraulic gear near engine, somehow run that line to the controller, then

the return line would be that one I showed under left foot of the dissassembled L295 and the bolt I pointed to of the assembled L295

let me know if I am on the right track

Now: go get the 6 fittings to go from 3/8 to jic 8, get the drill bit that fit snug on that threaded jic 8, get a few hydraulic hoses just in case

take those fittings with you and take one hose while you go around, dont make any mistake

exhaust manifold busted open, you can feel it affect the idle

got these fittings: 3/8 MIP to 1/2 FL

installed 6 fittings, got them connected to the hose successfully

titanium drill bit that will be used to drill out the seized thread, then the 3/8 thread should fit snug, weld on it if it leak

go work on drilling out those ports and successfully getting hose attached, then finish up steering wheel

might have got one in successfully: use your titanium bit, bore out the seized metal, hit with compress air, come in with the diesel on brush, screw in the fitting,

try to make it straight, then do the same on the other fitting

took out crooked fitting, hit with torch/diesel/air, then screw fitting in straight and put hose on properly

the other seized fitting: extract it with your titanium bit, burn new paint with torch, hit with air/diesel

unbelieveable, seized fitting came out intact, and screwed on cheap fitting successfully, connected hose

all 12 hoses successfully connected, cannot proceed forward until I solve the suction/return lines going to/from the controller

few task you can do while hydraulic problem linger: grind down the steering wheel smooth, hit it with black paint, fully seal the exhaust manifold crack, decide what fabric to get to cover the damaged seat, make progress on the hood install

there is a front frame assembly that screw into the front mount of the loader, start to consider that area and how the hood mount to it

at this point, only 2 hydrauic line are stopping her from carving earth...

make a bit more progress until darkness, then spend hours nighttime researching the hydraulic problem

grind down jb weld, hand sand with 600 grit dip in diesel, brush with solvent multiple time, hit with compress air, hit with cheap paint

study diagram, figure out bracket that hold the hood so it swing forward

other bracket bolts seized and busted stuck on the frame

dab with diesel, hit with torch hard, tried loosening, wont budge

next chance you work: escalate effort, take wheel off, take hood off, extract stuck bolts with drill bit

 

[Russell King]

@joesmith123

Look at this diagram. There are brackets #90 attached to the battery tray that the hood pivots on.
On many old tractors the battery tray is mostly a rusted mess so you may have to improvise a structure to get the hood up high enough off the frame so it can rotate around the hinge points.

I used some square tube material that has holes spaced on all four sides.

to tap into the tractor hydraulic system see this thread that shows how a block on many old tractors was used

B7100 Hydraulic block diverter (70060-00360 or 70070-00385)

CURRENTLY SOLD OUT. Making more is a winter project. I will remove this line when I have made more. These are obsolete and no longer available. I have recently been contacted by a member asking if I will make him one of these after reading how I made mine. I know this comes up from time to time...

www.orangetractortalks.com

In the diagram you posted earlier that block would be in line #50 which is the pump outlet. Line #10 is the suction side feeding fluid into the pump. You can just cut that pipe #50 in two and use compression fittings to extend the pump side to the FEL valve and then from the FEL valve power out you would connect to the rear half that would then power the three point hitch and dump into the sump (to be pulled into the pump again).

You need to decide which pump you want to use, the tractor pump or the PTO pump to power the FEL. How was it done on the tractor that the FEL came from?