New profile posts

What's new New posts New media New media comments New profile posts Latest activity
D
Hi, Lugbolt said you do a lot of instrument cluster repairs. I have a 2004 GMC and it had a remanufactured unit in it when I bought it used over2 years ago and have replaced it twice. Do you hire out?
SCP
Hello all, new member as of 15 Feb 2025, new tractor owner (M62), lurked around on this site for years, figured i'd join up and possibly contribute (pay back the community for all the info i've gleaned over the years). I have 10 acres of desert land (sagebrush) which I will start building on this year (2025).
T
Hi ChrisO83. I also have a B2782B Snowblower. I removed the PTO shield and can't get it back together because I can't get that metal snap ring back into place.

How did you manage to get the snap ring back where it belongs?

Thanks for any help.

Tim
GlueGuy
Still listed as "NEW" although i'm on my tenth Kubota and have been a member for many years!
M
BX1800 lights died. Fuse & switch are okay. NO POWER FEEDING INTO SWITCH. Where should I check next?
View previous comments…
M
Mike149
No, it’s been too cold here in Ohio!
  • Like
Reactions: 1 user
JimDeL
JimDeL
I know what you mean. I'm over in Austintown, North and East of you. Low temps and Lake Effect snow! What's not to like... :ROFLMAO:
M
Mike149
Hi Jim: I finally got back to trying to fix this "no headlight" issue & the plot has thickened! I now have intermittent power to the light switch but still no lights. If I unplug the cold wire from a headlight & run a new temp wire to ground, it worked (once). But then a few minutes later, I couldn't repeat it & discovered I'd again lost power feeding to the switch (hence my "intermittent" comment in second sentence). And to complicate matters, my fuel gauge has now died. I've given up & purchased a Milwaukee M18 portable work light with magnetic that I simply slap onto the hood when I need lights. Thanks for your above replies. Mike
S
need help with my gr2100 snowblower
K
k countryman
Have a lx3310 with 51 "front mount snowblower. Deflector is actuating , but chute rotation doesn't regardless the position of toggle switch. Toggle located on lever in cab. Loosened hydraulic connections and no obstructions and can turn chute by hand. Fuses are good. Any suggestions.
A
I have a B2630 I purchased new in 2011 the receiver end of the seat belt quit holding the ratchet in place I can hear it snap in place but a nice tug and it pops right out.
I am looking fo a replacement receiver end.
Mountainman
Mountainman
Thank you for the inquiry but unfortunately i wouldn't have any b2630 parts or anything that new.
C
Find a snow blower for your B7800?
B
b12
Yes. I have a Frontier SB1164 rear mount snowblower.
Andy c
Kubota u173a. 2012
All works ok apart from arm and tracks which I assumed was a faulty safety switch, I have checked this and all is ok, If I give it full revs I get minimal track movement and arm movement, I have removed the hydraulic pump and spline etc all intact so could it be the solenoid off the safety switch? If so where would that be located? I would very much appreciate any advice
Regards
T
I have an L245Dt and I am looking for the left side axle. My manual has a part number of 35110-2711. Does anyone out there have a used one for sale?
Thank you!
T
Tcmk
007kubotaguy has the parts you need .
Andy c
Kubota u173a. 2012
All works ok apart from arm and tracks which I assumed was a faulty safety switch, I have checked this and all is ok, If I give it full revs I get minimal track movement and arm movement, I have removed the hydraulic pump and spline etc all intact so could it be the solenoid off the safety switch? If so where would that be located? I would very much appreciate any advice
Regards
Top Bottom